Home > Machine Settings > Change Machine Settings from the Control Panel > Menu Table (for LCD Models) > Settings Tables (1 Line LCD models)
Settings Tables (1 Line LCD models)
[General Setup]
Level 1 | Level 2 | Level 3 | Description |
---|---|---|---|
Tray Setting | Paper Type | - | Set the type of paper in the paper tray. |
Paper Size | - | Set the size of paper. | |
Check Size | - | Select whether to display a message telling you to check that the size of the paper in the machine and the machine's Paper Size setting match. | |
Manual Feed | - | Select whether to print from the Manual Feed Slot. | |
Resolution | - | - | Choose a print resolution. |
Density | - | - | Increase or decrease the print density. |
Ecology | Eco Mode | - | Turn the following machine settings on at the same time.
|
Toner Save | - | Increase the page yield of the toner cartridge. | |
Sleep Time | - | Set how much time will pass before the machine enters Power Saving mode. | |
Quiet Mode | - | Decrease printing noise. | |
Auto Power Off | - | Set the number of hours that the machine will remain in Deep Sleep mode before going into Power Off mode. | |
Panel Control | Button Repeat | - | Set the time for the LCD message to change when holding or at intervals. |
Message Scroll | - | Set the time in seconds that an LCD message will scroll across the LCD. From Level 1=0.2 sec to Level 10=2.0 sec. | |
LCD Contrast | - | Adjust the contrast of the LCD. | |
Auto Online | - | Set the machine to return to Ready mode after it has been idle for 30 seconds. | |
Setting Lock | - | - | Lock your machine’s settings using the Setting Lock password. |
Interface | Select | - | Select the interface to use. If you select Auto, the machine changes the interface to USB or Network depending on which interface is receiving data. |
Auto IF Time | - | Set the time-out period for the auto interface selection. | |
Input Buffer | - | Increase or decrease the input buffer capacity. |
[Printer]
Level 1 | Level 2 | Description |
---|---|---|
Print Options | Font List | Print the font list and samples. |
Test Print | Print a test page. | |
2-sided (For automatic 2-sided printing models) | 2-sided Print | Turn 2-sided printing off or on and select flip on long edge or short edge. |
Single Image | For a print job where the last page is a 1-sided image, select the 1-sided Feed option to reduce printing time. | |
Auto Continue | - | Select if you want the machine to clear paper size errors or media type errors automatically. |
Paper Type | - | Set the type of paper. |
Paper Size | - | Set the size of paper. |
Copies | - | Set the number of printed pages. |
Orientation | - | Set pages to print in either portrait or landscape orientation. |
Print Position | X Offset | Move the print start position (at the top-left corner of pages) horizontally up to -500 (left) to +500 (right) dots in 300 dpi. |
Y Offset | Move the print start position (at the top-left corner of pages) vertically up to -500 (up) to +500 (down) dots in 300 dpi. | |
Auto FF | - | Allow the machine to print any remaining data automatically. |
HP LaserJet | Font No. | Set the font number. |
Font Pitch | Set the font pitch. The Font Pitch menu appears when you choose I012 to I018, I031 to I037 or I097 to I109 in Font No. setting. | |
Font Point | Set the font size. The Font Point menu appears when you choose I000 to I011, I019 to I030 or I038 to I096 in Font No. setting. | |
Symbol Set | Select the symbol or character set. | |
Table Print | Print the code table. | |
Auto LF | ON: CR -> CR+LF, OFF: CR -> CR | |
Auto CR | ON: LF -> LF+CR, FF -> FF+CR, or VT -> VT+CR OFF: LF -> LF, FF -> FF, or VT -> VT | |
Auto WRAP | Choose whether a line feed and carriage return will happen when the machine reaches the right margin. | |
Auto SKIP | Choose whether a line feed and carriage return will happen when the carriage position reaches the bottom margin. | |
Left Margin | Set the left margin at column 0 to 70 columns at 1 cpi. | |
Right Margin | Set the right margin at column 10 to 80 columns at 1 cpi. | |
Top Margin | Set the top margin distance from the top edge of the paper. | |
Bottom Margin | Set the bottom margin distance from the bottom edge of the paper. | |
Lines | Set the number of lines on each page. | |
Tray Command | Select this setting if a tray mismatch appears when you use the HP drivers. |
[Network] (HL-B2050DN)
Level 1 | Level 2 | Level 3 | Description |
---|---|---|---|
TCP/IP | Boot Method | - | Choose the IP method that best suits your needs. |
IP Address | - | Enter the IP address. | |
Subnet Mask | - | Enter the Subnet mask. | |
Gateway | - | Enter the Gateway address. | |
Node Name | - | Enter the Node name. | |
WINS Config | - | Select the WINS configuration mode. | |
WINS Server | Primary | Specify the IP address of the primary WINS server. | |
Secondary | Specify the IP address of the secondary WINS server. | ||
DNS Server | Primary | Specify the IP address of the primary DNS server. | |
Secondary | Specify the IP address of the secondary DNS server. | ||
APIPA | - | Allocate the IP address from the link-local address range automatically *1. | |
IPv6 | - | Enable or disable the IPv6 protocol. | |
Ethernet | - | - | Choose the Ethernet link mode. |
Wired Status | - | - | Display the Ethernet link status. |
MAC Address | - | - | Display the MAC address of the machine. |
Network Reset | - | - | Restore all network settings of your machine to the factory settings. |
[Print Reports]
Level 1 | Level 2 | Description |
---|---|---|
Printer Settings | - | Print the Printer Settings page. |
Network Config (For network models) | - | Print the Network Configuration Report. |
Print File List (Available only for certain models) | - | Print a list of data saved in the memory. |
Drum Dot Print | - | Print the Drum Dot Check Sheet. |
[Machine Info.]
Level 1 | Level 2 | Description |
---|---|---|
Serial No. | - | Display the machine's serial number. |
Firmware Version | - | Check your machine's firmware version. |
Page Counter | - | Display the total printed pages. |
Parts Life *1 | Toner Life | Display the remaining life of the toner cartridge. |
Drum Life | Display the remaining life of the drum unit. |
[Initial Setup]
Level 1 | Level 2 | Description |
---|---|---|
Reset | Machine Reset | Restore all the machine settings that you have changed. |
Network Reset | Restore all network settings back to the factory settings. | |
Factory Reset | Restores all the machine's settings to the factory defaults. Perform this operation when you dispose of your machine. | |
Local Language | - | Select the LCD language for your country. |