![]() ![]() | ![]() ![]() |
Submenu | Menu Selections | Options | Descriptions |
![]() | |||
Emulation (HL-3070CW only) | Choose the emulation mode you use. | ||
Auto Continue | Choose whether to automatically clear the removable error. | ||
Output Color (HL-3070CW only) | Set the output color. | ||
Media Type (HL-3070CW only) | Sets the type of paper. | ||
Paper (HL-3070CW only) | Sets the size of paper. | ||
Copies (HL-3070CW only) | Sets the number of printed pages. | ||
Orientation | This printer can print pages in portrait or landscape orientation. | ||
Print Position | X Offset | Moves the print start position (at the top-left corner of pages) horizontally up to -500 (left) to +500 (right) dots in 300 dpi. | |
Y Offset | Moves the print start position (at the top-left corner of pages) vertically up to -50 (up) to +500 (down) dots in 300 dpi. | ||
Auto FF (HL-3070CW only) | Allows you to print the remaining data without pressing Go. | ||
HP LaserJet (HL-3070CW only)
| Font No. | ||
Font Pitch | |||
Font Point | |||
Symbol Set | Sets the symbol set or the character set. | ||
Table Print |
Prints code table. If Change Emulation appears on the LCD, choose Auto or HP LaserJet in Emulation of Print Menu. (See Emulation (HL-3070CW only).) | ||
Auto LF | ON: CR ![]() ![]() | ||
Auto CR | ON: LF ![]() ![]() ![]() ![]() ![]() ![]() | ||
Auto WRAP | Chooses whether a line feed and carriage return will happen when the printer reaches the right margin. | ||
Auto SKIP | Chooses whether a line feed and carriage return will happen when the printer position reaches the bottom margin. | ||
Left Margin | ## | Sets the left margin at column 0 to 70 columns at 10 cpi. | |
Right Margin | ## | Sets the right margin at column 10 to 80 columns at 10 cpi. | |
Top Margin | #.## | Sets the top margin at a distance from the top edge of the paper: 0, 0.33, 0.5, 1.0, 1.5 or 2.0. The default setting is 0.5. | |
Bottom Margin | #.## | Sets the bottom margin at a distance from the bottom edge of the paper - 0, 0.33, 0.5, 1.0, 1.5 or 2.0. The default setting is 0.5. | |
Lines | #### | Sets the number of lines on each page from 5 to 128 lines. | |
BR-Script 3 (HL-3070CW only)
| Error Print | ||
CAPT |
Submenu | Menu Selections | Options | Descriptions |
![]() | |||
Boot Method | Choose the IP method that best suits your needs. | ||
IP Address | Enter the IP address. | ||
Subnet Mask | Enter the Subnet mask. | ||
Gateway | Enter the Gateway address. | ||
IP Boot Tries | |||
APIPA | Automatically allocates the IP address from the link-local address range.1 | ||
IPv6 | |||
Ethernet | Chooses Ethernet link mode. | ||
Factory Reset | Restores all network settings of the internal print server to the factory default. |
Submenu 1 | Submenu 2 | Menu Selections | Options | Descriptions |
![]() | ||||
Wired LAN | Boot Method | Choose the IP method that best suits your needs. | ||
IP Address | Enter the IP address. | |||
Subnet Mask | Enter the Subnet mask. | |||
Gateway | Enter the Gateway address. | |||
IP Boot Tries | ||||
APIPA | Automatically allocates the IP address from the link-local address range.1 | |||
IPv6 | ||||
Ethernet | Chooses Ethernet link mode. | |||
Set to Default | Restores wired network settings of the internal print server to the factory default. | |||
Wired Enable | Chooses Ethernet link mode. | |||
Boot Method | Choose the IP method that best suits your needs. | |||
IP Address | Enter the IP address. | |||
Subnet Mask | Enter the Subnet mask. | |||
Gateway | Enter the Gateway address. | |||
IP Boot Tries | ||||
APIPA | Automatically allocates the IP address from the link-local address range.1 | |||
IPv6 | ||||
SES/WPS/AOSS | ||||
WPS w/PIN Code | ||||
(Appears only when WLAN Enable is On.) | Status | |||
Signal | ||||
Channel | ||||
Speed | ||||
SSID | Shows SSID [uses a maximum of 32 digits and characters 0-9, a-z and A-Z in ASCII values] | |||
Comm. Mode | Shows the current Communication Mode. | |||
Set to Default | Restores wired network settings of the internal print server to the factory default. | |||
WLAN Enable | Chooses Ethernet link mode. | |||
Factory Reset | Restores all network settings of the internal print server to the factory default. |
Submenu | Menu Selections | Options | Descriptions |
![]() | |||
Color Calibration | Calibrate | Carry out calibration to revise the colors. (See Calibration.) | |
Reset | Set the calibration parameters back to the default settings. (See Calibration.) | ||
Auto Regist. | Registration | Adjusts the print position of each color automatically. (See Auto Registration.) | |
Frequency | Sets the interval time you want to carry out the auto registration. (See Auto Registration.) | ||
Manual Regist. | Print Chart | Prints the chart to manually check the registration of the colors. (See Manual Registration.) | |
Set Registration | 1 Magenta/2 Cyan/3 Yellow/4 Magenta/5 Cyan/6 Yellow/7 Magenta/8 Cyan/9 Yellow | Enter the correction value on the chart you printed from the Print Chart. (See Manual Registration.) | |
Drum Cleaning | Carry out cleaning the drum unit to improve the print quality problem. (See Small spots on the printed pages in Cleaning the drum unit.) |
Submenu | Menu Selections | Options | Descriptions |
![]() | |||
Paper Size | Sets the size of paper for direct print. | ||
Media Type | Sets the type of paper for direct print. | ||
Multiple Page | Sets the pattern if you want to print multiple pages on a single sheet or one page on multiple sheets. | ||
Orientation | This printer can print pages in portrait or landscape orientation. | ||
Collate | |||
Print Quality | |||
PDF Option | Set the information you want to add to the document. | ||
Index Print |
Sets the format of the index for direct print. If you choose Details, printing time will be longer. (See Printing data from a USB flash memory drive with direct print (HL-3070CW only).) |
1 | Press any of the Menu buttons (+, -, OK or Back) to take the printer offline. | ||
2 | Press + or - to choose Network.
| ||
3 |
| ||
4 | Press OK.
| ||
5 | Press OK.
| ||
6 | Press the - button.
| ||
7 | Press OK. The first part of the number will be blinking.
| ||
8 | Press + or - to increase or decrease the number. Press OK to go to the next number.
| ||
9 | Repeat step 8 until you have set your IP address.
| ||
10 | Press OK or Go to finish the IP address.
|
![]() ![]() | ![]() ![]() |