Tray Setting

Paper Type

-

Select the paper type that matches the paper in the standard paper tray.

Paper Size

-

Select the paper size you loaded in the standard paper tray.

Manual Feed

-

Select whether to print from the Manual Feed Slot.

Print Position

X Offset

Y Offset

Check Paper

-

Select whether to display a message telling you to check that the size of the paper in the machine and the machine's Paper Size setting match.

Ecology

Eco Mode

-

Turn the following machine settings on at the same time:

• 2-sided Print: Long Edge *1 (available for certain models)
• Sleep Time: 0Min
• Quiet Mode:On *1
• Toner Save:On *1

Toner Save

-

Increase the page yield of the toner cartridge.

Sleep Time

-

Set how much time should pass before the machine enters Power Saving mode.

Quiet Mode

-

Decrease printing noise.

Auto Power Off

-

Set the number of hours that the machine will remain in Deep Sleep mode before going into Power Off mode.

Panel Control

Button Repeat

-

Set the time for the LCD message to change when holding or .

Message Scroll

-

Set the time in seconds that an LCD message will scroll across the LCD. From Level 1 (0.2 s) to Level 10 (2 s).

LCD Contrast

-

Adjust the contrast of the LCD.

Auto Online

-

Set the machine to return to Ready mode after it has been idle for 30 seconds.

Setting Lock

-

-

Lock your machine’s settings using the Setting Lock password.

Interface

Select

-

Select the interface to use.

If you select Auto, the machine changes the interface to USB or network depending on which interface is receiving data.

Auto IF Time

-

Set the time-out period for the auto interface selection.

Input Buffer

-

Increase or decrease the input buffer capacity.

Emulation

-

-

Choose the emulation mode.

Quality

-

-

Select the print quality.

Print Options

Font List

HP LaserJet

Print the font list and samples of HP LaserJet.

BR-Script 3

Print the font list and samples of BR-Script.

Test Print

-

Print the test page.

2-sided

2-sided Print

-

Select whether to print on both sides of the paper.

Single Image

-

For a print job where the last page is a 1-sided image, select the 1-sided Feed option to reduce printing time.

When you use preprinted paper, you must select the 2-sided Feed option. If you select 1-sided Feed for preprinted paper, the last page will be printed on the reverse side.

Auto Continue

-

-

Select if you want the machine to clear paper size errors or media type errors automatically.

Output Colour

-

-

Set the output colour.

Paper Type

-

-

Set the paper type.

Paper Size

-

-

Set the paper size.

Copies

-

-

Set the number of printed pages.

Orientation

-

-

Set pages to print in either portrait or landscape orientation.

Edge Emphasis

-

-

Make the text appear sharper.

Print Position

X Offset

-

Move the print start position (at the upper left corner of pages) horizontally from -500 (left) to +500 (right) dots in 300 dpi.

Y Offset

-

Move the print start position (at the upper left corner of pages) vertically from -500 (up) to +500 (down) dots in 300 dpi.

Auto FF

-

-

Allow the machine to print any remaining data automatically.

HP LaserJet

Font No.

-

Set the font number.

Font Pitch

-

Set the font pitch.

(Available only for certain fonts.)

Font Point

-

Set the font size.

(Available only for certain fonts.)

Symbol Set

-

Select the symbol or character set.

Table Print

-

Print the code table.

Auto LF

-

ON: CR -> CR+LF, OFF: CR -> CR

Auto CR

-

ON: LF -> LF+CR, FF -> FF+CR, or VT -> VT+CR

OFF: LF -> LF, FF -> FF, or VT -> VT

Auto WRAP

-

Select whether you want a line feed and carriage return when the carriage position reaches the right margin.

Auto SKIP

-

Select whether you want a line feed and carriage return when the carriage position reaches the bottom margin.

Left Margin

-

Set the left margin at column 0 to 70 columns at 1 cpi.

Right Margin

-

Set the right margin at column 10 to 80 columns at 1 cpi.

Top Margin

-

Set the top margin distance from the top edge of the paper.

Bottom Margin

-

Set the bottom margin distance from the bottom edge of the paper.

Lines

-

Set the number of lines on each page.

Tray Command

-

Select this setting if a tray mismatch appears when you use the HP drivers.

BR-Script 3

Error Print

-

Choose whether the machine prints the error information when errors occur.

CAPT

-

Use CAPT (Colour Advanced Printing Technology) for optimal print quality when printing a PS file created by a non-Brother PS driver.

Colours and photos appear clearer and more accurate. Print speed will be slower.

PDF

Multiple Page

-

Set the page layout when printing multiple pages.

PDF Print Opt

-

Fit to Page

-

ColourCorrection

Correction Start

-

Initiate colour calibration to check and correct colours.

Reset

-

Reset the calibration parameters to the default settings.

Auto Correction

-

Set the machine to perform Colour Calibration and Registration automatically.

Colour Settings

Setting Mode

Select whether to apply the colour print settings of the machine or the printer driver.

Colour Mode

Select the colour mode.

Improve Gray

Turn on or off to improve the image quality of shaded areas.

Enhance Black

Turn on or off if a black graphic does not print correctly.

Brightness

Adjust the brightness.

Contrast

Adjust the contrast.

Red

Adjust the red colour.

Green

Adjust the green colour.

Blue

Adjust the blue colour.

Reset Printer

-

-

Restore the machine settings to the factory settings.

Wired LAN

TCP/IP

Boot Method

-

Choose the IP method that best suits your needs.

IP Address

-

Enter the IP address.

Subnet Mask

-

Enter the Subnet mask.

Gateway

-

Enter the Gateway address.

Node Name

-

Enter the Node name.

WINS Config

-

Select the WINS configuration mode.

WINS Server

Primary

Specify the IP address of the primary WINS server.

Secondary

Specify the IP address of the secondary WINS server.

DNS Server

Primary

Specify the IP address of the primary DNS server.

Secondary

Specify the IP address of the secondary DNS server.

APIPA

-

Allocate the IP address from the link-local address range automatically *1.

IPv6

-

Turn the IPv6 protocol on or off.

Ethernet

-

-

Choose the Ethernet link mode.

Wired Status

-

-

Display the wired network connection status.

MAC Address

-

-

Display your machine's MAC address.

Set to Default

-

-

Restore your machine's wired network settings to the factory settings.

Wired Enable

-

-

Turn the wired interface on or off.

WLAN(Wi-Fi)

Find Network

-

-

Configure the wireless network settings using the setup wizard.

TCP/IP

Boot Method

-

Choose the IP method that best suits your needs.

IP Address

-

Enter the IP address.

Subnet Mask

-

Enter the Subnet mask.

Gateway

-

Enter the Gateway address.

Node Name

-

Enter the Node name.

WINS Config

-

Select the WINS configuration mode.

WINS Server

Primary

Specify the IP address of the primary WINS server.

Secondary

Specify the IP address of the secondary WINS server.

DNS Server

Primary

Specify the IP address of the primary DNS server.

Secondary

Specify the IP address of the secondary DNS server.

APIPA

-

Allocate the IP address from the link-local address range automatically *1.

IPv6

-

Turn the IPv6 protocol on or off.

WPS/Push Button

-

-

Configure your wireless network settings using the one-button push method.

WPS/PIN Code

-

-

Configure the wireless network settings using WPS with a PIN code.

WLAN Status

Status

-

Display the wireless network connection status.

Signal

-

Display the wireless network signal strength.

Channel

-

Display the channel in use when Status is Active.

Speed

-

Display the connection speed when Status is Active.

SSID

-

Display the wireless SSID (Network Name).

Comm. Mode

-

Display the current Communication mode.

MAC Address

-

-

Display your machine's MAC address.

Set to Default

-

-

Restore your machine's wireless network settings to the factory settings.

WLAN Enable

-

-

Turn the wireless interface on or off.

Wi-Fi Direct

Manual

-

-

Configure your Wi-Fi Direct network settings manually.

Group Owner

-

-

Set your machine as the Group Owner.

Push Button

-

-

Configure your Wi-Fi Direct network settings using the one-button push method quickly.

PIN Code

-

-

Configure your Wi-Fi Direct network settings using WPS with a PIN code quickly.

Device Info.

Device Name

-

View your machine's device name.

SSID

-

Display the Group Owner's SSID (Network Name).

IP Address

-

Display your machine's IP Address.

Status Info.

Status

-

Display the Wi-Fi Direct network status.

Signal

-

Display the current Wi-Fi Direct network signal strength.

When your machine acts as Group Owner, the LCD always displays Strong.

Channel

-

Display the channel in use when the Status is G/O Active or Client Active.

Speed

-

Display the connection speed when the Status is G/O Active or Client Active.

I/F Enable

-

-

Enable or disable the Wi-Fi Direct connection.

Web Based Mgmt

-

-

-

If you enable this function, make sure you specify the connection method to use Web Based Management.

-

-

-

IPsec is an optional security feature of the IP protocol that provides authentication and encryption services. We recommend contacting your network administrator before changing this setting.

-

-

-

-

Network Reset

-

-

-

Restore all network settings of your machine to the factory settings.

Printer Settings

-

Print the Printer Settings page.

-

Print the Network Configuration Report.

Print File List

-

Print a list of data saved in the memory.

Drum Dot Print

-

Print the Drum Dot Check Sheet.

-

Print the wireless connection diagnostics report.

Serial No.

-

Display the machine's serial number.

Firmware Version

Main Version

Display the machine's firmware version.

Security Version

Page Counter

Total

Display the total number of printed pages.

Colour

Display the total colour printed pages.

Black and White

Display the total monochrome printed pages.

Parts Life *1

Toner

Display the remaining life of each toner.

Drum

Display the remaining life of each drum unit.

Belt

Display the remaining life of the belt unit.

Fuser

Display the remaining life of the fuser unit.

Reset

Machine Reset

Restore all the machine settings that you have changed.

Network Reset

Restore all network settings back to the factory settings.

Factory Reset

Restore all the machine's settings to the factory defaults. Perform this operation when you dispose of your machine.

Local Language

-

Select the LCD language for your country.