(Date & Time)

-

-

Access the Date and Time setting menus.

Toner

Toner Life

-

View the approximate remaining toner life.

Test Print

-

Print a test page.

Colour Correction

Colour Correction

Initiate colour calibration to check and correct colours.

Reset

Reset the calibration parameters to the default settings.

Toner Cartridge Check

Black

Magenta

Cyan

Yellow

View the installed toner cartridge information on the LCD, for example, if the toner cartridge is genuine.

Network

Wired LAN

-

Access the Wired LAN setting menus.

WLAN(Wi-Fi)

-

Access the WLAN setting menus.

Tray Setting

-

-

Access the tray setting menus.

Wi-Fi Direct

-

-

Access the Wi-Fi Direct setting menus.

Eco Mode

-

-

Turn the following machine settings on at the same time:

• 2-sided Print: Long Edge (available for certain models) *1
• Sleep Time: 0Min
• Dim Timer: 10Secs
• Quiet Mode:On *1
• Toner Save:On *1

All Settings

-

-

Configure the detailed settings.

Tray Setting

Paper Type

-

Select the paper type that matches the paper in the standard paper tray.

Paper Size

-

Select the paper size you loaded in the standard paper tray.

Print Position

X Offset

Adjust the print start position (usually at the upper left corner of a page) for the paper you loaded in the MP tray horizontally from -500 (left) to +500 (right) dots when printing at 300 dpi.

Y Offset

Adjust the print start position (usually at the upper left corner of a page) for the paper you loaded in the MP tray vertically from -500 (up) to +500 (down) dots when printing at 300 dpi.

Check Paper

-

Select whether or not to display a message indicating you must check the paper type and paper size when you pull a paper tray out of the machine.

Beep

-

-

Adjust the beeper volume.

LCD Settings

Backlight

-

Adjust the brightness of the LCD backlight.

Dim Timer

-

Set how long the LCD backlight stays on after you go back to your Main Home screen and other functions.

Screen Settings

Home Screen

-

Set the Main Home screen.

Scan Screen

-

Set the default Scan screen.

Display Information

IP Address

Select whether or not to display your machine's IP Address on the Home screens.

Notice Settings

Scan Result(Skip Blank Page)

-

Displays the total scanned pages and skipped pages after scanning is completed.

Ecology

Eco Mode

-

Turn the following machine settings on at the same time:

• 2-sided Print: Long Edge (available for certain models) *1
• Sleep Time: 0Min
• Dim Timer: 10Secs
• Quiet Mode:On *1
• Toner Save:On *1

Toner Save

-

Increase the page yield of the toner cartridge.

Sleep Time

-

Set how much time should pass before the machine enters Power Saving mode.

Quiet Mode

-

Decrease printing noise.

Auto Power Off

-

Set the number of hours that the machine will remain in Deep Sleep mode before going into Power Off mode.

Setting Lock

-

-

Restrict unauthorised users from changing the machine’s settings.

Delete Storage

Macro ID

-

Delete the registered Macro data.

Stream ID

-

Delete the registered Stream data.

Font ID

-

Delete the registered Font data.

Delete All

-

Restore your machine's Macro/Stream and Font data to the factory settings.

(Select a Shortcut)

Rename

Change the shortcut name.

Edit

Change the shortcut settings.

Delete

Delete the shortcut.

Emulation

-

-

Select the emulation mode.

Quality

-

-

Select the print quality.

Print Options

Font List

HP LaserJet

Print a list of the machine’s internal fonts.

BR-Script 3

Test Print

-

Print a test page.

Print the red colour patch

-

Print the red colour patch page.

2-sided

2-sided Print

-

Enable or disable 2-sided printing and choose long edge or short edge.

Single Image

-

For a print job where the last page is a 1-sided image, select the 1-sided Feed option to reduce printing time.

When you use preprinted paper, you must select the 2-sided Feed option. If you select 1-sided Feed for preprinted paper, the last page will be printed on the reverse side.

Auto Continue

-

-

Select if you want the machine to clear paper size errors or media type errors automatically, and use paper from other trays.

Output Colour

-

-

Set the output colour.

Paper Type

-

-

Set the paper type.

Paper Size

-

-

Set the paper size.

Copies

-

-

Set the number of printed pages.

Orientation

-

-

Set pages to print in either portrait or landscape orientation.

Edge Emphasis

-

-

Make the text appear sharper.

Print Position

-

-

Access the Print Position setting menus.

Auto FF

-

-

Allow the machine to print any remaining data automatically.

HP LaserJet

Font No.

Font No.

Set the font number.

This menu appears if a soft font is installed on your Brother machine.

Soft Font No.

Set the soft font number.

This menu appears if a soft font is installed on your Brother machine.

Font Pitch

-

Set the font pitch.

(Available only for certain fonts.)

Font Point

-

Set the font size.

(Available only for certain fonts.)

Symbol Set

-

Select the symbol or character set.

Table Print

-

Print the code table.

Auto LF

-

ON: CR -> CR+LF, OFF: CR -> CR

Auto CR

-

ON: LF -> LF+CR, FF -> FF+CR, or VT -> VT+CR

OFF: LF -> LF, FF -> FF, or VT -> VT

Auto WRAP

-

Select whether you want a line feed and carriage return when the carriage position reaches the right margin.

Auto SKIP

-

Select whether you want a line feed and carriage return when the carriage position reaches the bottom margin.

Left Margin

-

Set the left margin at column 0 to 70 columns at 1 cpi.

Right Margin

-

Set the right margin at column 10 to 80 columns at 1 cpi.

Top Margin

-

Set the top margin distance from the top edge of the paper.

Bottom Margin

-

Set the bottom margin distance from the bottom edge of the paper.

Lines

-

Set the number of lines on each page.

Tray Command

-

Select this setting if a tray mismatch appears when you use the HP drivers.

BR-Script 3

Error Print

-

Choose whether the machine prints the error information when errors occur.

CAPT

-

Use CAPT (Colour Advanced Printing Technology) for optimal print quality when printing a PS file created by a non-Brother PS driver.

Colours and photos appear clearer and more accurate. Print speed will be slower.

PDF

Multiple Page

-

Set the page layout when printing multiple pages.

PDF Print Options

-

Set the PDF Print setting to print either comments (Markup) or stamps in the PDF file, along with the text.

PDF Fit to Page

-

Select if the machine scales or resizes the pages in the PDF file to fit the selected paper size.

Colour Correction

Correction Start

-

Perform colour calibration to check and correct colours, and then perform registration to align the print position of each colour.

Reset

-

Reset the calibration parameters to the default settings.

Auto Correction

-

Set the machine to perform Colour Calibration and Registration automatically.

Colour Settings

Setting Mode

Select whether to apply the colour print settings of the machine or the printer driver.

Colour Mode

Select the colour mode.

Improve Gray Colour

Turn on or off to improve the image quality of shaded areas.

Enhance Black Printing

Turn on or off if a black graphic does not print correctly.

Brightness

Adjust the brightness.

Contrast

Adjust the contrast.

Red

Adjust the red colour.

Green

Adjust the green colour.

Blue

Adjust the blue colour.

Reset Printer

-

-

Restore the machine settings to the factory settings.

Wired LAN

TCP/IP

Boot Method

-

Select the Boot method that best suits your needs.

IP Address

-

Enter the IP address.

Subnet Mask

-

Enter the Subnet mask.

Gateway

-

Enter the Gateway address.

Node Name

-

Enter the Node name.

(up to 32 characters)

WINS Configuration

-

Select the WINS configuration mode.

WINS Server

Primary

Specify the IP address of the primary WINS server.

Secondary

Specify the IP address of the secondary WINS server.

DNS Server

Primary

Specify the IP address of the primary DNS server.

Secondary

Specify the IP address of the secondary DNS server.

APIPA

-

Set the machine to allocate the IP address from the link-local address range automatically.

IPv6

-

Turn the IPv6 protocol on or off.

Ethernet

-

-

Select the Ethernet link mode.

Wired Status

-

-

View the current wired status.

MAC Address

-

-

View the machine's MAC address.

Set to Default

-

-

Restore the wired network settings to the factory settings.

Wired Enable

-

-

Turn the Wired LAN interface on or off manually.

WLAN(Wi-Fi)

Find Wi-Fi Network

-

-

Configure your wireless network settings manually.

TCP/IP

Boot Method

-

Select the Boot method that best suits your needs.

IP Address

-

Enter the IP address.

Subnet Mask

-

Enter the Subnet mask.

Gateway

-

Enter the Gateway address.

Node Name

-

Enter the Node name.

(up to 32 characters)

WINS Configuration

-

Select the WINS configuration mode.

WINS Server

Primary

Specify the IP address of the primary WINS server.

Secondary

Specify the IP address of the secondary WINS server.

DNS Server

Primary

Specify the IP address of the primary DNS server.

Secondary

Specify the IP address of the secondary DNS server.

APIPA

-

Set the machine to allocate the IP address from the link-local address range automatically.

IPv6

-

Turn the IPv6 protocol on or off.

WPS/Push Button

-

-

Configure your wireless network settings using the one-button push method.

WPS/PIN Code

-

-

Configure your wireless network settings using WPS with a PIN.

WLAN Status

Status

-

View the current wireless network status.

Signal

-

View the current wireless network signal strength.

SSID

-

View the current SSID.

Comm. Mode

-

View the current Communication mode.

MAC Address

-

-

View the machine's MAC address.

Set to Default

-

-

Restore the wireless network settings to the factory settings.

WLAN Enable

-

-

Turns the wireless interface on or off.

Wi-Fi Direct

Manual

-

-

Configure your Wi-Fi Direct network settings manually.

Group Owner

-

-

Set your machine as the Group Owner.

Push Button

-

-

Configure your Wi-Fi Direct network settings using the one-button push method.

PIN Code

-

-

Configure your Wi-Fi Direct network settings using WPS with a PIN code.

Device Information

Device Name

-

View your machine's device name.

SSID

-

View the Group Owner's SSID.

When the machine is not connected, the LCD displays Not Connected.

IP Address

-

View your machine's current IP Address.

Status Information

Status

-

View the current Wi-Fi Direct network status.

Signal

-

View the current Wi-Fi Direct network signal strength.

When your machine acts as Group Owner, the LCD always indicates a strong signal.

I/F Enable

-

-

Turn the Wi-Fi Direct connection on or off.

Web Based Mgmt

-

-

-

Enable or disable Web Based Management.

If you enable this function, make sure you specify the connection method to use Web Based Management.

IPsec

-

-

-

IPsec is an optional security feature of the IP protocol that provides authentication and encryption services. We recommend contacting your network administrator before changing this setting.

Global Detect

Allow Detect

-

-

Enable or disable Global Detect, a function that detects and notifies the user when the user unintentionally connects to a global network.

Reject Access

-

-

Disable connections to the global network.

Network Reset

-

-

-

Restore all network settings back to the factory settings.

User Settings

-

Print a list of your User settings.

Printer Settings

-

Print a list of your Printer settings.

Network Configuration

-

Print a list of your Network settings.

Print File List

-

Print a list of data saved in the machine's memory.

Drum Dot Print

-

Print the Drum Dot Check Sheet.

WLAN Report

-

Print the wireless LAN connection results.

Serial No.

-

-

Check your machine's serial number.

Firmware Version

Main Version

-

Check your machine's firmware version.

Security Version

-

Firmware Update

-

-

Update your machine to the latest firmware.

Firmware Auto Check

-

-

View firmware information on the Main Home screen.

Page Counter

Total

Colour

Check the total number of pages the machine has printed.

Black and White

Copy

Colour

Black and White

Print

Colour

Black and White

Other

Colour

Black and White

Parts Life *1

Drum

Black(BK)

Display the remaining life of each drum unit.

Cyan(C)

Magenta(M)

Yellow(Y)

Belt

-

Display the remaining life of the belt unit.

Fuser

-

Display the remaining life of the fuser unit.

Date & Time

Date

Set the date and time on your machine.

Time

Clock Type

Select the time format (12-hour or 24-hour).

Time Zone

Set your time zone.

Reset

Machine Reset

Restore the machine settings that you have changed.

Network Reset

Restore all network settings back to the factory settings.

All Settings

Restore all the machine's settings back to the factory settings and delete the personal data in the memory. You cannot see the data on the machine.

Factory Reset

Restore all the machine settings back to the factory settings and delete the personal data in the machine's memory. We recommend using this menu option if you want to delete all the data from the machine.

Local Language

(Available only for certain countries)

-

Change your LCD language.