Search

Home > Network > Wireless Network Settings > Use the Wireless Network > Configure Your Machine for a Wireless Network When the SSID Is Not Broadcast

Configure Your Machine for a Wireless Network When the SSID Is Not Broadcast

HL-L3220CW/HL-L3220CDW/HL-L3240CDW

Before configuring your machine, we recommend writing down your wireless network settings. You will need this information before you continue with the configuration.

  1. Check and write down the current wireless network settings.
    Network Name (SSID)
      
    Authentication Method Encryption Mode Network Key
    Open System NONE -
    WEP
    Shared Key WEP
    WPA/WPA2-PSK AES
    TKIP
    WPA3-SAE AES

    For example:

    Network Name (SSID)
    HELLO
    Authentication Method Encryption Mode Network Key
    WPA2-PSK AES 12345678
    image
    If your router uses WEP encryption, enter the key used as the first WEP key. Your Brother machine supports the use of the first WEP key only.
  2. Press image or image to select the [Network] option, and then press OK.
  3. Press image or image to select the [WLAN(Wi-Fi)] option, and then press OK.
  4. Press image or image to select the [Find Network] option, and then press OK.
  5. When [WLAN Enable?] appears, select On.
    This will start the wireless setup wizard.
  6. The machine will search for your network and display a list of available SSIDs. Press image or image to select the [<New SSID>] option, and then press OK.
  7. Enter the SSID name, and then press OK.
  8. Press image or image to select the Authentication Method you want, and then press OK.
  9. Do one of the following:
    • If you selected the [Open System] option, press image or image to select the Encryption Type [None] or [WEP], and then press OK.

      If you selected the [WEP] option for Encryption Type, enter the WEP key, and then press OK.

    • If you selected the [Shared Key] option, enter the WEP key, and then press OK.
    • If you selected the [WPA-Personal] option, press image or image to select the Encryption Type [TKIP+AES] or [AES], and then press OK.

      Enter the WPA key, and then press OK.

    • If you selected the [WPA3-SAE] option, select the Encryption Type [AES], and then press OK.

      Enter the WPA key, and then press OK.

    image
    Your Brother machine supports the use of the first WEP key only.
  10. To apply the settings, select [Yes].
  11. The machine will attempt to connect to the wireless device you have selected.
If your wireless device is connected successfully, the machine's LCD displays [Connected].

You have completed the wireless network setup. To install the drivers and software necessary to use your machine, go to your model's Downloads page at support.brother.com/downloads.

HL-L3280CDW/HL-L8240CDW

Before configuring your machine, we recommend writing down your wireless network settings. You will need this information before you continue with the configuration.

  1. Check and write down the current wireless network settings.
    Network Name (SSID)
      
    Authentication Method Encryption Mode Network Key
    Open System NONE -
    WEP
    Shared Key WEP
    WPA/WPA2-PSK AES
    TKIP
    WPA3-SAE AES

    For example:

    Network Name (SSID)
    HELLO
    Authentication Method Encryption Mode Network Key
    WPA2-PSK AES 12345678
    image
    If your router uses WEP encryption, enter the key used as the first WEP key. Your Brother machine supports the use of the first WEP key only.
  2. Press image [Settings]>[All Settings]>[Network]>[WLAN(Wi-Fi)]>[Find Wi-Fi Network].
  3. When [Enable WLAN?] appears, press [Yes].
    This will start the wireless setup wizard. To cancel, press [No].
  4. The machine will search for your network and display a list of available SSIDs. Press image or image to display the [<New SSID>] option.
  5. Press [<New SSID>], and then press [OK].
  6. Enter the SSID name, and then press [OK].
  7. Select the Authentication Method.
  8. Do one of the following:
    • If you selected the [Open System] option, press [None] or [WEP].

      If you selected the [WEP] option for Encryption type, enter the WEP key, and then press [OK].

    • If you selected the [Shared Key] option, enter the WEP key, and then press [OK].
    • If you selected the [WPA/WPA2-PSK/WPA3-SAE] option, press [TKIP+AES] or [AES].

      Enter the WPA key, and then press [OK].

    • If you selected the [WPA3-SAE] option, press [AES].

      Enter the WPA key, and then press [OK].

    image
    Your Brother machine supports the use of the first WEP key only.
  9. The machine attempts to connect to the wireless device you have selected.
If your wireless device is connected successfully, the machine's LCD displays [Connected]. Press [OK].

You have completed the wireless network setup. To install the drivers or the application necessary for operating your machine, go to your model's Downloads page at support.brother.com/downloads.

Did you find the information you needed?