Search

Settings Tables (HL-L3270CDW)

Related Models:HL‑L3270CDW

image [Settings]

Level 2

Level 3

Level 4

Descriptions

Toner

Toner Life

-

View the approximate remaining toner life.

Test Print

-

Print a test page.

Calibration

Calibrate

Initiate colour calibration to check and correct colours.

Reset

Reset the calibration parameters to the default settings.

Registration

-

Align the print position of each colour.

Network

-

-

Access the Network setting menus.

Tray Setting

-

-

Access the tray setting menus.

Wi-Fi Direct

-

-

Access the Wi-Fi Direct setting menus.

Eco Mode

-

-

Turn the following machine settings on at the same time.

  • 2-sided Print: Long Edge (Available only for certain models)
  • Sleep Time: 0 Min
  • Dim Timer: 10 Secs

All Settings

-

-

Configure the detailed settings.

[All Settings]>[General Setup]

Level 3

Level 4

Descriptions

Tray Setting

Paper Type

Select the paper type that matches the paper in the tray.

Paper Size

Select the size of paper you loaded in the tray.

Check Size

Select whether to display a message telling you to check that the size of the paper in the machine and the machine's Paper Size setting match.

Manual Feed

Select whether to print from the Manual Feed Slot.

LCD Settings

Backlight

Adjust the brightness of the LCD backlight.

Dim Timer

Set how long the LCD backlight stays on after the last finger press.

Ecology

Eco Mode

Turn the following machine settings on at the same time.

  • 2-sided Print: Long Edge (Available only for certain models)
  • Sleep Time: 0 Min
  • Dim Timer: 10 Secs

Toner Save

Increase the page yield of the toner cartridge.

Sleep Time

Set how much time will pass before the machine enters Power Saving mode.

Quiet Mode

Decrease printing noise.

Auto Power Off

Set the number of hours that the machine will remain in Deep Sleep mode before going into Power Off mode.

Setting Lock

Set Password

Restrict unauthorised users from changing the machine’s settings.

Lock Off⇒On

Interface

Select

Select the interface to use.

If you select the Auto option, the machine changes the interface to USB or Network depending on which interface is receiving data.

Auto IF Time

Set the time-out period for the auto interface selection.

Input Buffer

Increase or decrease the input buffer capacity.

Delete Storage

Macro ID

Delete the registered Macro data.

Font ID

Delete the registered Font data.

Format

Restore the Macro and Font data of your machine to the default settings.

[All Settings]>[Printer]

Level 3

Level 4

Level 5

Descriptions

Emulation

-

-

Choose the emulation mode.

Quality

-

-

Select the print quality.

Print Options

Font List

HP LaserJet

Print the font list and samples of HP LaserJet.

BR-Script 3

Print the font list and samples of BR-Script.

Test Print

-

Print the test page.

2-sided

2-sided Print

-

Select whether to print on both sides of the paper.

Single Image

-

For a print job where the last page is a 1-sided image, select the 1-sided Feed option to reduce printing time.

When you use preprinted paper, you must select the 2-sided Feed option. If you select 1-sided Feed for preprinted paper, the last page will be printed on the reverse side.

Auto Continue

-

-

Select if you want the machine to clear paper size errors or media type errors automatically, and use paper from other trays.

Output Colour

-

-

Set the output colour.

Paper Type

-

-

Set the type of paper.

Paper Size

-

-

Set the size of paper.

Copies

-

-

Set the number of printed pages.

Orientation

-

-

Set pages to print in either portrait or landscape orientation.

Print Position

X Offset

-

Move the print start position (at the top-left corner of pages) horizontally up to -500 (left) to +500 (right) dots in 300 dpi.

Y Offset

-

Move the print start position (at the top-left corner of pages) vertically up to -500 (up) to +500 (down) dots in 300 dpi.

Auto FF

-

-

Allow the machine to print any remaining data automatically.

HP LaserJet

Font No.

Font No.

Set the font number.

Soft Font No.

Set the soft font number.

This menu appears if a soft font is installed on your Brother machine.

Font Pitch

-

Set the font pitch.

(Available for certain font numbers)

Font Point

-

Set the font size.

(Available for certain font numbers)

Symbol Set

-

Select the symbol or character set.

Table Print

-

Print the code table.

Auto LF

-

ON: CR -> CR+LF, OFF: CR -> CR

Auto CR

-

ON: LF -> LF+CR, FF -> FF+CR, or VT -> VT+CR

OFF: LF -> LF, FF -> FF, or VT -> VT

Auto WRAP

-

Choose whether a line feed and carriage return will happen when the machine reaches the right margin.

Auto SKIP

-

Choose whether a line feed and carriage return will happen when the carriage position reaches the bottom margin.

Left Margin

-

Set the left margin at column 0 to 70 columns at 1 cpi.

Right Margin

-

Set the right margin at column 10 to 80 columns at 1 cpi.

Top Margin

-

Set the top margin distance from the top edge of the paper.

Bottom Margin

-

Set the bottom margin distance from the bottom edge of the paper.

Lines

-

Set the number of lines on each page.

Tray Command

-

Select this setting if a tray mismatch appears when you use the HP drivers.

BR-Script 3

Error Print

-

Choose whether the machine prints the error information when errors occur.

CAPT

-

Use CAPT (Colour Advanced Printing Technology) for optimal print quality when printing a PS file created by a non-Brother PS driver.

Colours and photos appear clearer and more accurate. Print speed will be slower.

Colour Correction

Calibration

Calibrate

Initiate colour calibration to check and correct colours.

Reset

Reset the calibration parameters to the default settings.

Registration

-

Align the print position of each colour.

Auto Correction

-

Set the machine to perform Colour Calibration and Registration automatically.

Colour Settings

Setting Mode

Select whether to apply the colour print settings of the machine or the printer driver.

Colour Mode

Select the colour mode.

Improve Gray Colour

Turn on or off to improve the image quality of shaded areas.

Enhance Black Printing

Turn on or off if a black graphic does not print correctly.

Brightness

Adjust the brightness.

Contrast

Adjust the contrast.

Red

Adjust the red colour.

Green

Adjust the green colour.

Blue

Adjust the blue colour.

[All Settings]>[Network]

Level 3

Level 4

Level 5

Level 6

Descriptions

Wired LAN

TCP/IP

Boot Method

-

Choose the IP method that best suits your needs.

IP Address

-

Enter the IP address.

Subnet Mask

-

Enter the Subnet mask.

Gateway

-

Enter the Gateway address.

Node Name

-

Enter the Node name.

WINS Configuration

-

Select the WINS configuration mode.

WINS Server

Primary

Specify the IP address of the primary WINS server.

Secondary

Specify the IP address of the secondary WINS server.

DNS Server

Primary

Specify the primary DNS server's IP address.

Secondary

Specify the secondary DNS server's IP address.

APIPA

-

Allocate the IP address from the link-local address range automatically *1.

IPv6

-

Turn the IPv6 protocol on or off. For more detailed information, go to your model's FAQs & Troubleshooting page on the Brother support website at support.brother.com.

Ethernet

-

-

Choose the Ethernet link mode.

Wired Status

-

-

Display the Ethernet link status.

MAC Address

-

-

Display the MAC address of the machine.

Set to Default

-

-

Restore wired network settings of your machine to the factory settings.

Wired Enable

-

-

Turn the wired interface on or off.

WLAN

TCP/IP

Boot Method

-

Choose the IP method that best suits your needs.

IP Address

-

Enter the IP address.

Subnet Mask

-

Enter the Subnet mask.

Gateway

-

Enter the Gateway address.

Node Name

-

Enter the Node name.

WINS Configuration

-

Select the WINS configuration mode.

WINS Server

Primary

Specify the IP address of the primary WINS server.

Secondary

Specify the IP address of the secondary WINS server.

DNS Server

Primary

Specify the primary DNS server's IP address.

Secondary

Specify the secondary DNS server's IP address.

APIPA

-

Allocate the IP address from the link-local address range automatically *1.

IPv6

-

Turn the IPv6 protocol on or off. For more detailed information, go to your model's FAQs & Troubleshooting page on the Brother support website at support.brother.com.

Setup Wizard

-

-

Configure the wireless network settings using the setup wizard.

WLAN Assistant

-

-

Configure your wireless network settings using the Brother installation disc.

WPS

-

-

Configure your wireless network settings using the one-button push method.

WPS w/ PIN Code

-

-

Configure the wireless network settings using WPS with a PIN code.

WLAN Status

Status

-

Display the wireless Ethernet link status.

Signal

-

Display the signal condition.

SSID

-

Display SSID.

Comm. Mode

-

Display the current Communication mode.

MAC Address

-

-

Display the MAC address of the machine.

Set to Default

-

-

Restore wireless network settings of your machine to the factory settings.

WLAN Enable

-

-

Turn the wireless interface on or off.

Wi-Fi Direct

Push Button

-

-

Configure your Wi-Fi Direct network settings using the one-button push method quickly.

PIN Code

-

-

Configure your Wi-Fi Direct network settings using WPS with a PIN code quickly.

Manual

-

-

Configure your Wi-Fi Direct network settings manually.

Group Owner

-

-

Set your machine as the Group Owner.

Device Information

Device Name

-

View your machine's device name.

SSID

-

Display the Group Owner's SSID.

IP Address

-

Display your machine's IP Address.

Status Information

Status

-

Display the Wi-Fi Direct network status.

Signal

-

Display the current Wi-Fi Direct network signal strength.

I/F Enable

-

-

Enable or disable the Wi-Fi Direct connection.

NFC

-

-

-

Turn the NFC function on or off.

Web Connect Settings

Proxy Settings

Proxy Connection

-

Change the web connection settings.

Address

-

Port

-

User Name

-

Password

-

Network Reset

-

-

-

Restore all network settings of your machine to the factory settings.

*1
On connection to the network, if the machine's ‘Boot Method’ is ‘Auto’ the machine will attempt to set the IP address and Subnet Mask from a boot server such as DHCP. If a boot server cannot be found, an APIPA IP address will be allocated, such as 169. 254. [001-254]. [000-255]. If the ‘Boot Method’ of the machine is set to ‘Static’ you must manually enter an IP address from the machine's control panel.

[All Settings]>[Print Reports]

Level 3

Descriptions

Printer Settings

Print the Printer Settings page.

Network Configuration

Print the Network Configuration Report.

Print File List

Print a list of data saved in the memory.

Drum Dot Print

Print the Drum Dot Check Sheet.

WLAN Report

Print the wireless LAN connectivity diagnosis result.

[All Settings]>[Machine Information]

Level 3

Level 4

Descriptions

Serial No.

-

Display the machine's serial number.

Firmware Version

Main Version

Display the main firmware version.

Sub1 Version

Display the sub firmware version.

Firmware Update

-

Update your machine to the latest firmware.

Firmware Auto Check

-

View firmware information on the Home screen.

Page Counter

Total

Display the total printed pages.

Colour

Display the total colour printed pages.

Black and White

Display the total monochrome printed pages.

Parts Life *1

Drum

Display the remaining life of each drum unit.

Belt

Display the remaining life of the belt unit.

Fuser

Display the remaining life of the fuser unit.

PF Kit 1

Display the remaining life of the PF Kit 1.

*1
Life is approximate and may vary by type of use.

[All Settings]>[Initial Setup]

Level 3

Level 4

Descriptions

Reset

Machine Reset

Restore all the machine's settings that you have changed, such as Paper Type.

Network Reset

Restore all network settings of your machine to the factory settings.

Factory Reset

Reset the machine and restore the printer settings (including command settings) to the factory settings.

Local Language

-

Select the LCD language for your country.

Did you find the information you needed?