Search

Home > Troubleshooting > Error and Maintenance Messages

Error and Maintenance Messages

image
  • HL-L3270CDW

    If the LCD displays errors and your Android device supports the NFC feature, touch your device to the NFC symbol on your Brother machine to access the Brother Solutions Center and browse the latest FAQs from your device. (Your mobile telephone provider's message and data rates may apply.)

    Make sure the NFC settings of both your Brother machine and your Android device are set to On.

As with any sophisticated office product, errors may occur and supply items may have to be replaced. If this happens, your machine identifies the error or required routine maintenance and shows the appropriate message. The most common error and maintenance messages are shown in the table.

Follow the instructions in the Action column to solve the error and remove the message.

You can correct most errors and perform routine maintenance by yourself. If you need more tips: Visit support.brother.com, and click the FAQs & Troubleshooting page.

HL-L3210CW/HL-L3230CDW

Error Message Cause Action

2-sided Disabled

The back cover of the machine is not closed completely.

Close the back cover of the machine until it locks in the closed position.

Access Denied

The function you want to use is restricted by Secure Function Lock 3.0.

Ask your administrator to check your Secure Function Lock Settings.

Belt End Soon

The belt unit is near the end of its life.

Order a new belt unit before the LCD displays Replace Belt.

Calibrate

Calibration failed.

  • Press and hold down image to turn the machine off. Wait a few seconds, and then turn it on again. Perform the colour calibration again using the control panel.

  • Install a new belt unit.

  • If the problem continues, contact Brother customer service or your local Brother dealer.

Cartridge Error

The toner cartridge is not installed correctly.

Remove the toner cartridge and drum unit assembly for the colour that is indicated on the LCD. Take out the toner cartridge, and put it back into the drum unit again. Re-install the toner cartridge and drum unit assembly back in the machine.

If the problem continues, contact Brother customer service or your local Brother dealer.

Condensation

Condensation may have formed inside the machine after a room temperature change.

Leave the machine turned on. Wait for 30 minutes with the top cover in the open position. Then turn off the machine and close the cover. Turn it on again.

Cooling Down

The temperature of the inside of the machine is too hot. The machine pauses its current print job and goes into cooling down mode.

Wait until the machine has finished cooling down. Make sure all vents on the machine are clear of obstructions.

When the machine has cooled down, it will resume printing.

Cover is Open

The top cover is not completely closed.

Open and then firmly close the top cover of the machine.

Cover is Open

The fuser cover is not completely closed.

Close the fuser cover located inside the back cover of the machine.

Drum !

The corona wires on the drum unit must be cleaned.

Clean the corona wires on the drum unit.

image

See Related Information: Clean the Corona Wires.

If the problem continues, replace the drum unit with a new one.

Drum End Soon

The drum unit is near the end of its life.

Order a new drum unit before the LCD displays Replace Drum.

Drum Stop

It is time to replace the drum unit.

Replace the drum unit.

See Related Information: Replace the Drum Unit.

Jam 2-sided

The paper is jammed underneath the paper tray or the fuser unit.

Remove the paper tray or open the back cover to gently remove the jammed paper.

Jam Inside

The paper is jammed inside the machine.

Open the top cover, remove the toner cartridges and drum unit assembly, and gently remove the jammed paper. Reinstall the toner cartridges and drum unit assemblies into the machine. Close the top cover.

Jam Manual Feed

The paper is jammed in the manual feed slot of the machine.

Gently remove the jammed paper from in and around the manual feed slot. Reload the paper into the manual feed slot, and then press Go.

Jam Rear

The paper is jammed in the back of the machine.

Open the fuser cover and gently remove the jammed paper. Close the fuser cover.

Jam Tray 1

The paper is jammed in the indicated paper tray.

Pull out the paper tray and gently remove all jammed paper.

Limit Exceeded

The print limit set in Secure Function Lock 3.0 was reached.

Ask your administrator to check your Secure Function Lock Settings.

Manual Feed

Manual was selected as the paper source in the printer driver, but there is no paper in the manual feed slot.

Place paper in the manual feed slot.

Media Mismatch

The media type specified in the printer driver differs from the paper type specified in the machine's menu.

Load the correct type of paper in the tray, and then select the correct media type in the Paper Type setting on the machine.

No Belt Unit

The belt unit is not installed or not installed correctly.

Reinstall the belt unit.

No Drum Unit

The drum unit is not installed correctly.

Reinstall the toner cartridges and drum unit assembly.

No Paper T1

The machine failed to feed paper from the indicated paper tray.

Do one of the following:

  • Refill paper in the paper tray indicated on the LCD. Make sure the paper guides are set to the correct size.
  • If paper is in the tray, remove it and load it again. Make sure the paper guides are set to the correct size.
  • Do not overfill the paper tray.

No Toner

The toner cartridge is not installed or not installed correctly.

Remove the toner cartridge and drum unit assembly. Remove the toner cartridge from the drum unit, and reinstall the toner cartridge back into the drum unit. Reinstall the toner cartridge and drum unit assembly back in the machine. If the problem continues, replace the toner cartridge.

No Tray T1

The paper tray is not installed or not installed correctly.

Reinstall the paper tray indicated on the LCD.

No Waste Toner

The waste toner box is not installed or not installed correctly.

Reinstall the waste toner box.

Out of Memory

The machine’s memory is full.

Press and hold Go for about two seconds and reduce the print resolution.

Print Data Full

The machine’s memory is full.

Press Cancel and delete the previously stored secure print data.

Print Unable ##

The machine has a mechanical problem.

  • Press and hold image to turn the machine off, wait a few minutes, and then turn it on again.

  • If the problem continues, contact Brother customer service.

Registration

Registration failed.

  • If the error continues, press and hold down image to turn the machine off.

    Wait a few seconds, and then turn on the machine again.

    Perform the colour registration using the control panel.

  • Install a new belt unit.

  • If the problem continues, contact Brother customer service or your local Brother dealer.

Replace Belt

It is time to replace the belt unit.

Replace the belt unit with a new one.

See Related Information: Replace the Belt Unit.

Replace Drum

It is time to replace the drum unit.

Replace the drum unit for the colour indicated on the LCD.

See Related Information: Replace the Drum Unit.

If this message is displayed even after replacing the drum unit with new one, the drum unit counter was not reset.

Reset the drum unit counter.

See Related Information: Replace the Drum Unit.

Replace Toner

The toner cartridge is at the end of its life. The machine stops all print operations.

Replace the toner cartridge for the colour indicated on the LCD.

See Related Information: Replace the Toner Cartridge.

Replace WT Box

It is time to replace the waste toner box.

Replace the waste toner box with a new one.

See Related Information: Replace the Waste Toner Box.

Self-Diagnostic

The temperature of the fuser unit does not rise to a specified temperature within the specified time.

Press and hold image to turn the machine off, wait a few seconds, and then turn it on again. Leave the machine idle for 15 minutes with the power on.

The fuser unit is too hot.

Short paper

The length of the paper in the tray is too short for the machine to deliver it to the Face down output tray.

Open the back cover (Face up output tray) to let the printed page exit onto the Face up output tray. Remove the printed pages, and then press Go.

Size Error DX

The paper size specified in the machine's paper size setting is not available for automatic 2-sided printing.

Press Cancel (if required).

Load the correct size of paper in the tray and set the tray for that paper size.

Choose a paper size supported by 2-sided printing.

Paper size available for automatic 2-sided printing is A4.

The paper in the tray is not the correct size and is not available for automatic 2-sided printing.

Size Error

The paper size defined in the printer driver is not supported by the defined tray.

Choose a paper size supported by the defined tray.

Size Mismatch

The paper in the tray is not the correct size.

Load the correct size of paper in the tray and set the size of paper for the tray. Press Go.

Toner Error

One or more toner cartridges are not installed or not installed correctly.

Pull out the drum units. Remove all the toner cartridges, and then put them back into the drum units.

Toner Low: BK

Toner Low: C

Toner Low: M

Toner Low: Y

(BK=Black, C=Cyan, M=Magenta, Y=Yellow.)

If the LCD displays this message, you can still print. The toner cartridge is near the end of its life.

Order a new toner cartridge before the LCD displays Replace Toner.

WT Box End Soon

The waste toner box is almost full.

Order a new waste toner box before the LCD displays Replace WT Box.

HL-L3270CDW

Error Message Cause Action

2-sided Disabled

The back cover of the machine is not closed completely.

Close the back cover of the machine until it locks in the closed position.

Access Denied

The function you want to use is restricted by Secure Function Lock 3.0.

Ask your administrator to check your Secure Function Lock Settings.

Calibration

Calibration failed.

  • Press and hold down image to turn the machine off. Wait a few seconds, and then turn it on again. Perform the colour calibration again using the LCD.

  • Install a new belt unit.

  • If the problem continues, contact Brother customer service or your local Brother dealer.

Cartridge Error

The toner cartridge is not installed correctly.

Remove the toner cartridge and drum unit assembly for the colour that is indicated on the LCD. Take out the toner cartridge, and put it back into the drum unit again. Install the toner cartridge and drum unit assembly back in the machine.

If the problem continues, contact Brother customer service or your local Brother dealer.

Condensation

Condensation may have formed inside the machine after a room temperature change.

Leave the machine turned on. Wait for 30 minutes with the top cover in the open position. Then turn off the machine and close the cover. Turn it on again.

Cooling Down

The temperature of the inside of the machine is too hot. The machine pauses its current print job and goes into cooling down mode.

Wait until the machine has finished cooling down. Make sure all vents on the machine are clear of obstructions.

When the machine has cooled down, it will resume printing.

Cover is Open

The top cover is not completely closed.

Open and then firmly close the top cover of the machine.

Cover is Open

The fuser cover is not completely closed.

Close the fuser cover located inside the back cover of the machine.

Drum !

The corona wires on the drum unit must be cleaned.

Clean the corona wires on the drum unit.

image

See Related Information: Clean the Corona Wires.

If the problem continues, replace the drum unit with a new one.

Drum Stop

It is time to replace the drum unit.

Replace the drum unit.

See Related Information: Replace the Drum Unit.

Jam 2-sided

The paper is jammed underneath the paper tray or the fuser unit.

Remove the paper tray or open the back cover to gently remove the jammed paper.

Jam Inside

The paper is jammed inside the machine.

Open the top cover, remove the toner cartridges and drum unit assembly, and gently remove the jammed paper. Reinstall the toner cartridges and drum unit assemblies into the machine. Close the top cover.

Jam Manual Feed

The paper is jammed in the manual feed slot of the machine.

Gently remove the jammed paper from in and around the manual feed slot. Reload the paper into the manual feed slot, and then press Retry.

Jam Rear

The paper is jammed in the back of the machine.

Open the fuser cover and gently remove the jammed paper. Close the fuser cover. If the error message remains, press Retry.

Jam Tray1

The paper is jammed in the indicated paper tray.

Pull out the paper tray and gently remove all jammed paper as shown in the animation on the LCD.

Limit Exceeded

The print limit set in Secure Function Lock 3.0 was reached.

Ask your administrator to check your Secure Function Lock Settings.

Manual Feed

Manual was selected as the paper source in the printer driver, but there is no paper in the manual feed slot.

Place paper in the manual feed slot.

Media Type Mismatch

The media type specified in the printer driver differs from the paper type specified in the machine's menu.

Load the correct type of paper in the tray indicated on the LCD, and then select the correct media type in the Paper Type setting on the machine.

No Belt Unit

The belt unit is not installed or not installed correctly.

Reinstall the belt unit.

No Drum Unit

The drum unit is not installed correctly.

Reinstall the toner cartridges and drum unit assembly.

No Paper Tray1

The machine failed to feed paper from the indicated paper tray.

Do one of the following:

  • Refill paper in the paper tray indicated on the LCD. Make sure the paper guides are set to the correct size.
  • If paper is in the tray, remove it and load it again. Make sure the paper guides are set to the correct size.
  • Do not overfill the paper tray.

No Toner

The toner cartridge is not installed or not installed correctly.

Remove the toner cartridge and drum unit assembly. Remove the toner cartridge from the drum unit, and reinstall the toner cartridge back into the drum unit. Reinstall the toner cartridge and drum unit assembly back in the machine. If the problem continues, replace the toner cartridge.

No Tray1

The paper tray is not installed or not installed correctly.

Reinstall the paper tray indicated on the LCD.

No Waste Toner

The waste toner box is not installed or not installed correctly.

Reinstall the waste toner box.

Out of Memory

The machine’s memory is full.

Press image and reduce the print resolution.

Print Data Full

The machine’s memory is full.

Press image and delete the previously stored secure print data.

Print Unable ##

The machine has a mechanical problem.

  • Press and hold image to turn the machine off, wait a few minutes, and then turn it on again.

  • If the problem continues, contact Brother customer service.

Registration

Registration failed.

  • Press and hold down image to turn the machine off. Wait a few seconds, and then turn it on again. Perform the colour registration again using the LCD.

  • Install a new belt unit.

  • If the problem continues, contact Brother customer service or your local Brother dealer.

Replace Toner

The toner cartridge is at the end of its life. The machine stops all print operations.

Replace the toner cartridge for the colour indicated on the LCD.

See Related Information: Replace the Toner Cartridge.

Replace WT Box

It is time to replace the waste toner box.

Replace the waste toner box with a new one.

See Related Information: Replace the Waste Toner Box.

Screen Init. Fail

The touchscreen was pressed before the power on initialisation was completed.

Make sure nothing is touching the touchscreen.

Debris may be stuck between the lower part of the touchscreen and its frame.

Insert a piece of stiff paper between the lower part of the touchscreen and its frame and slide it back and forth to push out any debris.

Self-Diagnostic

The temperature of the fuser unit does not rise to a specified temperature within the specified time.

Press and hold image to turn the machine off, wait a few seconds, and then turn it on again. Leave the machine idle for 15 minutes with the power on.

The fuser unit is too hot.

Short paper

The length of the paper in the tray is too short for the machine to deliver it to the Face down output tray.

Open the back cover (Face up output tray) to let the printed page exit onto the Face up output tray. Remove the printed pages, and then press Retry.

Size Error 2-sided

The paper size specified in the machine's paper size setting is not available for automatic 2-sided printing.

Press image (if required).

Load the correct size of paper in the tray and set the tray for that paper size.

Choose a paper size supported by 2-sided printing.

Paper size available for automatic 2-sided printing is A4.

The paper in the tray is not the correct size and is not available for automatic 2-sided printing.

Size Error

The paper size defined in the printer driver is not supported by the defined tray.

Choose a paper size supported by the defined tray.

Size Mismatch

The paper in the tray is not the correct size.

Load the correct size of paper in the tray and set the size of paper for the tray. Press Retry.

Supplies

Belt End Soon

The belt unit is near the end of its life.

Order a new belt unit before the LCD displays Replace Belt.

Supplies

Drum End Soon

The drum unit is near the end of its life.

Order a new drum unit before the LCD displays Replace Drum.

Supplies

Replace Belt

It is time to replace the belt unit.

Replace the belt unit with a new one.

See Related Information: Replace the Belt Unit.

Supplies

Replace Drum

It is time to replace the drum unit.

Replace the drum unit for the colour indicated on the LCD.

See Related Information: Replace the Drum Unit.

If this message is displayed even after replacing the drum unit with new one, the drum unit counter was not reset.

Reset the drum unit counter.

See Related Information: Replace the Drum Unit.

Supplies

Toner Low: X

(X indicates the toner cartridge or drum unit colour that is near the end of its life. BK=Black, C=Cyan, M=Magenta, Y=Yellow.)

If the LCD displays this message, you can still print. The toner cartridge is near the end of its life.

Order a new toner cartridge before the LCD displays Replace Toner.

Supplies

WT Box End Soon

The waste toner box is almost full.

Order a new waste toner box before the LCD displays Replace WT Box.

Toner Error

One or more toner cartridges are not installed or not installed correctly.

Pull out the drum units. Remove all the toner cartridges, and then put them back into the drum units.

Did you find the information you needed?