Error message | Action |
Access Error | The USB device was removed while data was processing. Press Cancel. Reinsert the USB device and try to print with Direct Print or PictBridge. |
Cartridge Error | Pull out the drum unit. Take out the toner cartridge that is indicated on the second line of LCD and put it back into the printer again. |
Cover is Open | Close the cover that is indicated on the second line of LCD. |
DIMM Error | Turn off the printer. Re-install the DIMM correctly. Wait a few seconds, and then turn it on again. If this error message appears again, replace the DIMM with a new one. See Installing extra memory. |
Drum Error | Clean the corona wires. (See Cleaning the corona wires.) |
EL Error | Open the front cover and close it again. |
Fuser Error | Turn the power switch off, wait a few seconds and then turn it again. Leave the printer for 15 minutes with the power on. |
Jam XXX | Carefully pull out the jammed paper from the area shown in Paper jams and how to clear them. |
Low Temperature | Allow the machine to warm up. |
Manual Feed | Put the same size of paper in the MP tray as is shown on the LCD. If the printer is 'paused', press Go. |
No Belt Unit | Install the belt unit. (See Belt unit.) |
No Drum Unit | Install the drum unit. (See Drum unit) |
No Paper | Put paper in the indicated empty tray. |
No Tray | Put the tray1 in the printer. |
No Waste Toner | Install the Waste Toner Box. (See Waste toner box.) |
Out Of Memory | Add more memory. (See Installing extra memory.) |
Size Error | Check the printer driver setting and put the correct sized paper in tray that is indicated on the second line of LCD. (See About paper.) |
Size Error DX | You can only use Letter, Legal or Folio size for duplex printing. Check the printer driver setting. Put the correct size of paper, which is indicated on the second line of the LCD, in the tray. (See About paper.) |
Size Mismatch | Put the same size paper in the paper tray or MP tray that is selected in the printer driver, and then press Go, or select the size of paper you set in the Tray Size setting from the control panel. |
Toner Life End | It is time to replace the toner cartridge. (See Replacing a toner cartridge.) |
Tray2 Error | Take out Tray2 and push it back in firmly. |
Unusable Device | Remove the USB flash memory drive from USB Direct Interface. |
Waste Toner Full | It is time to replace the Waste Toner Box. (See Replacing the waste toner box.) |
Call service message | Action | ||||||||||
Calibrate <Second line of the LCD>Calibration failed. See Troubleshooting chapter in User's guide. |
| ||||||||||
Registration <Second line of the LCD>Registration failed. See Troubleshooting chapter in User's guide. |
|
Error message | Meaning | Action |
The four marks (also , =blinking ) indicate the Black (K), Yellow (Y), Magenta (M), Cyan (C) toner cartridges from left to right. When the mark blinks (shown as in left), the indicated color toner is nearly empty. When the toner becomes empty, the indicator disappears completely. | Buy a new toner cartridge before you get a Toner Life End message. | |
Change Belt Unit | It is time to replace the belt unit. | Replace the belt unit. |
Change PF KitXX | It is time to replace the paper feeding kit XX. | Replace the paper feeding kit. |
Drum End Soon | It is time to replace the drum unit. | Replace the drum unit. (See Replacing the drum unit.) |
Fuser Unit End | It is time to replace the fuser unit. | Replace the fuser unit. |
Laser Unit End | It is time to replace the laser unit. | Replace the laser unit. |
Waste Toner Soon | The waste toner box is almost full. | Be ready to replace the waste toner box. (See Replacing the waste toner box.) |