Home PrintPrevious Next

Enhance Photos

You can edit and add effects to your photos and view them on the LCD before printing.
Note Note
•
After adding each effect, you can enlarge the view of the image by pressing Ink Management. To go back to the original size, press Ink Management again.
•
The Enhance Photos feature is supported by technology from Reallusion, Inc. Graphic

Auto Correct

Auto Correct is available for most photos. The machine decides the suitable effect for your photo.
1
Make sure you have put the memory card or USB Flash memory drive in the correct slot.
Press Graphic (Photo Capture).
2
Press Bsymbol.utri or Bsymbol.dtri to choose Enhance Photos.
Press OK.
3
Press Bsymbol.ltri or Bsymbol.rtri to choose your photo.
Press OK.
4
Press Bsymbol.utri or Bsymbol.dtri to choose Auto Correct.
Press OK.
Note Note
If Remove Red-Eye appears on the LCD, press Bsymbol.utri to attempt to remove red-eye from your photo.
5
Press OK. Then press + or - repeatedly to enter the number of copies you want.
6
Do one of the following:
•
Press OK and change the print settings. (See PhotoCapture Center™ print settings.)
•
If you do not want to change any settings, press Colour Start to print.
Page Top

Enhance Skin-Tone

Enhance Skin-Tone is best used for adjusting portrait photographs. It detects human skin colour in your photos and adjusts the image.
1
Make sure you have put the memory card or USB Flash memory drive in the correct slot.
Press Graphic (Photo Capture).
2
Press Bsymbol.utri or Bsymbol.dtri to choose Enhance Photos.
Press OK.
3
Press Bsymbol.ltri or Bsymbol.rtri to choose your photo.
Press OK.
4
Press Bsymbol.utri or Bsymbol.dtri to choose Enhance Skin-Tone.
Press OK.
5
Do one of the following:
•
Press OK if you do not want to change any settings.
•
Press Bsymbol.utri or Bsymbol.dtri to adjust the effect level manually. Press OK when you have finished.
6
Press + or - repeatedly to enter the number of copies you want.
7
Do one of the following:
•
Press OK and change the print settings. (See PhotoCapture Center™ print settings.)
•
If you do not want to change any settings, press Colour Start to print.
Page Top

Enhance Scenery

Enhance Scenery is best used for adjusting landscape photographs. It highlights green and blue areas in your photo, so that the landscape looks more sharp and vivid.
1
Make sure you have put the memory card or USB Flash memory drive in the correct slot.
Press Graphic (Photo Capture).
2
Press Bsymbol.utri or Bsymbol.dtri to choose Enhance Photos.
Press OK.
3
Press Bsymbol.ltri or Bsymbol.rtri to choose your photo.
Press OK.
4
Press Bsymbol.utri or Bsymbol.dtri to choose Enhance Scenery.
Press OK.
5
Do one of the following:
•
Press OK if you do not want to change any settings.
•
Press Bsymbol.utri or Bsymbol.dtri to adjust the effect level manually. Press OK when you have finished.
6
Press + or - repeatedly to enter the number of copies you want.
7
Do one of the following:
•
Press OK and change the print settings. (See PhotoCapture Center™ print settings.)
•
If you do not want to change any settings, press Colour Start to print.
Page Top

Remove Red-Eye

The machine detects eyes in your photos and will attempt to remove red-eye from your photo.
Note Note
There are some cases when red-eye may not be removed.
•
When the face is too small in the image.
•
When the face is turning too far up, down, left or right.
1
Make sure you have put the memory card or USB Flash memory drive in the correct slot.
Press Graphic (Photo Capture).
2
Press Bsymbol.utri or Bsymbol.dtri to choose Enhance Photos.
Press OK.
3
Press Bsymbol.ltri or Bsymbol.rtri to choose your photo.
Press OK.
4
Press Bsymbol.utri or Bsymbol.dtri to choose Remove Red-Eye.
Press OK.
•
When Remove Red-Eye is successful, the photo with the effect is shown. The adjusted part is shown in a red frame. Press OK.
•
When Remove Red-Eye is unsuccessful, Unable to Detect. is shown.
Press OK to go back to the previous level.
Note Note
Press Bsymbol.utri to try Remove Red-Eye again.
5
Press + or - repeatedly to enter the number of copies you want.
6
Do one of the following:
•
Press OK and change the print settings. (See PhotoCapture Center™ print settings.)
•
If you do not want to change any settings, press Colour Start to print.
Page Top

Monochrome

You can convert your photo to monochrome.
1
Make sure you have put the memory card or USB Flash memory drive in the correct slot.
Press Graphic (Photo Capture).
2
Press Bsymbol.utri or Bsymbol.dtri to choose Enhance Photos.
Press OK.
3
Press Bsymbol.ltri or Bsymbol.rtri to choose your photo.
Press OK.
4
Press Bsymbol.utri or Bsymbol.dtri to choose Monochrome.
Press OK.
5
Press OK. Then press + or - repeatedly to enter the number of copies you want.
6
Do one of the following:
•
Press OK and change the print settings. (See PhotoCapture Center™ print settings.)
•
If you do not want to change any settings, press Colour Start to print.
Page Top

Sepia

You can convert the colour of your photo to sepia.
1
Make sure you have put the memory card or USB Flash memory drive in the correct slot.
Press Graphic (Photo Capture).
2
Press Bsymbol.utri or Bsymbol.dtri to choose Enhance Photos.
Press OK.
3
Press Bsymbol.ltri or Bsymbol.rtri to choose your photo.
Press OK.
4
Press Bsymbol.utri or Bsymbol.dtri to choose Sepia.
Press OK.
5
Press OK. Then press + or - repeatedly to enter the number of copies you want.
6
Do one of the following:
•
Press OK and change the print settings. (See PhotoCapture Center™ print settings.)
•
If you do not want to change any settings, press Colour Start to print.
Page Top
Home PrintPrevious Next