Tray Setting

Paper Type

-

Set the type of paper in the paper tray.

Paper Size

-

Set the paper size in the paper tray.

Print Position

X Offset

Y Offset

Check Paper

-

Select whether or not to display a message indicating you must check the paper type and paper size when you pull a paper tray out of the machine.

Beep

-

-

Adjust the beeper volume.

Notifications

Blank Pg Skips

-

Displays the skipped pages after scanning is completed.

Ecology

Eco Mode

-

Turn on the following machine settings at the same time:

• 2-sided Print: Long Edge *1 (available for certain models)
• Sleep Time: 0Min
• Quiet Mode:On *1
• Toner Save:On *1

Toner Save

-

Increase the page yield of the toner cartridge.

Sleep Time

-

Set the number of minutes before the machine enters Sleep mode.

Quiet Mode

-

Decrease printing noise.

Auto Power Off

-

Set the number of hours that the machine will remain in Deep Sleep mode before going into Power Off mode.

LCD Contrast

-

-

Adjust the LCD contrast.

Setting Lock

-

-

Restrict unauthorized users from changing the machine’s settings.

Delete Storage

Macro ID

-

Delete the registered Macro data.

Stream ID

-

Delete the registered Stream data.

Font ID

-

Delete the registered Font data.

Delete All

-

Restore your machine's Macro/Stream and Font data to the factory settings.

Density

-

Adjust the density.

Quality

-

Choose the Copy resolution for your type of document.

Contrast

-

Adjust the contrast for copies.

Color Adjust

Red

Adjust the red color.

Green

Adjust the green color.

Blue

Adjust the blue color.

ID Copy

Density

Adjust the density.

Quality

Choose the Copy resolution for your type of document.

Contrast

Adjust the contrast for copies.

2in1/1in1

Make 2 in 1 ID copies.

Emulation

-

-

Set the printer emulation mode.

Quality

-

-

Select the print quality.

Print Options

Font List

HP LaserJet

Print a list of the machine’s internal fonts.

BR-Script 3

Test Print

-

Print a test page.

2-sided

2-sided Print

-

Turn 2-sided printing off or on and select flip on long edge or short edge.

Single Image

-

For a print job where the last page is a 1-sided image, select the 1-sided Feed option to reduce printing time.

When you use preprinted paper, you must select the 2-sided Feed option. If you select 1-sided Feed for preprinted paper, the last page will be printed on the reverse side.

Auto Continue

-

-

Select this setting if you want the machine to clear paper size errors or media type errors, and use paper from other trays.

Output Color

-

-

Set the output color.

Paper Type

-

-

Set the paper type.

Paper Size

-

-

Set the paper size.

Copies

-

-

Set the number of printed pages.

Orientation

-

-

Set pages to print in either portrait or landscape orientation.

Edge Emphasis

-

-

Make the text appear sharper.

PrintPosition

X Offset

-

Y Offset

-

Auto FF

-

-

Allow the machine to print any remaining data automatically.

HP LaserJet

Font No.

-

Set the font number.

Font Pitch

-

Set the font pitch.

(Available only for certain fonts.)

Font Point

-

Set the font size.

(Available only for certain fonts.)

Symbol Set

-

Select the symbol or character set.

Table Print

-

Print the code table.

Auto LF

-

ON: CR -> CR+LF, OFF: CR -> CR

Auto CR

-

ON: LF -> LF+CR, FF -> FF+CR, or VT -> VT+CR

OFF: LF -> LF, FF -> FF, or VT -> VT

Auto WRAP

-

Select whether you want a line feed and carriage return when the carriage position reaches the right margin.

Auto SKIP

-

Select whether you want a line feed and carriage return when the carriage position reaches the bottom margin.

Left Margin

-

Set the left margin at column 0 to 70 columns at 1 cpi.

Right Margin

-

Set the right margin at column 10 to 80 columns at 1 cpi.

Top Margin

-

Set the top margin distance from the top edge of the paper.

Bottom Margin

-

Set the bottom margin distance from the bottom edge of the paper.

Lines

-

Set the number of lines on each page.

Tray Command

-

Select this setting if a tray mismatch appears when you use the HP drivers.

BR-Script 3

Error Print

-

Choose whether the machine prints the error information when errors occur.

CAPT

-

Use CAPT (Color Advanced Printing Technology) for optimal print quality when printing a PS file created by a non-Brother PS driver.

Colors and photos appear clearer and more accurate. Print speed will be slower.

PDF

Multiple Page

-

Set the page layout when printing multiple pages.

PDF Print Opt

-

Set the PDF Print setting to print either comments (Markup) or stamps in the PDF file, along with the text.

Fit to Page

-

Select if the machine scales or resizes the pages in the PDF file to fit the selected paper size.

ClrCorrection

Correction

-

Initiate color calibration to check and correct colors.

Reset

-

Reset the calibration parameters to the default settings.

Auto Correct

-

Set the machine to perform Color Calibration and Registration automatically.

Color Settings

Setting Mode

Select whether to apply the color print settings of the machine or the printer driver.

Color Mode

Select the color mode.

Improve Gray

Turn on or off to improve the image quality of shaded areas.

Enhance Black

Turn on or off if a black graphic does not print correctly.

Brightness

Adjust the brightness.

Contrast

Adjust the contrast.

Red

Adjust the red color.

Green

Adjust the green color.

Blue

Adjust the blue color.

Reset Printer

-

-

Restore the machine settings to the factory settings.

WLAN(Wi-Fi)

Find Network

-

-

Configure the wireless network settings using the setup wizard.

TCP/IP

Boot Method

-

Select the Boot method that best suits your needs.

IP Address

-

Enter the IP address.

Subnet Mask

-

Enter the Subnet mask.

Gateway

-

Enter the Gateway address.

Node Name

-

Enter the Node name.

(Up to 32 characters)

WINS Config

-

Select the WINS configuration mode.

WINS Server

Primary

Specify the IP address of the primary WINS server.

Secondary

Specify the IP address of the secondary WINS server.

DNS Server

Primary

Specify the IP address of the primary DNS server.

Secondary

Specify the IP address of the secondary DNS server.

APIPA

-

Set the machine to allocate the IP address from the link-local address range automatically.

IPv6

-

Turn the IPv6 protocol on or off.

WPS/PushButton

-

-

Configure your wireless network settings using the one-button push method.

WPS/PIN Code

-

-

Configure your wireless network settings using WPS with a PIN.

WLAN Status

Status

-

View the current wireless network status.

Signal

-

View the current wireless network signal strength.

Channel

-

View the current wireless network channel.

Speed

-

View the current wireless network speed.

SSID

-

View the current SSID.

Comm. Mode

-

View the current Communication mode.

MAC Address

-

-

View the machine's MAC address.

WLAN Enable

-

-

Turn the WLAN on or off manually.

Wi-Fi Direct

Manual

-

-

Configure your Wi-Fi Direct network settings manually.

Group Owner

-

-

Set your machine as the Group Owner.

Push Button

-

-

Configure your Wi-Fi Direct network settings using the one-button push method.

PIN Code

-

-

Configure your Wi-Fi Direct network settings using WPS with a PIN code.

Device Info.

Device Name

-

View your machine's device name.

SSID

-

View the Group Owner's SSID.

When the machine is not connected, the LCD displays Not Connected.

IP Address

-

View your machine's current IP Address.

Status Info.

Status

-

View the current Wi-Fi Direct network status.

Signal

-

View the current Wi-Fi Direct network signal strength.

When your machine acts as Group Owner, the LCD always indicates a strong signal.

Channel

-

View the current Wi-Fi Direct network channel.

Speed

-

View the current Wi-Fi Direct network speed.

I/F Enable

-

-

Turn the Wi-Fi Direct connection on or off.

Web Based Mgmt

-

-

-

If you enable this function, make sure you specify the connection method to use Web Based Management.

IPsec

-

-

-

IPsec is an optional security feature of the IP protocol that provides authentication and encryption services. We recommend contacting your network administrator before changing this setting.

Global Detect

Allow Detect

-

-

Reject Access

-

-

Network Reset

-

-

-

Restore all network settings back to the factory settings.

User Settings

Print a list of your User settings.

Print Settings

Print a list of your Printer settings.

Network Config

Print a list of your Network settings.

PrintFileList

Print a list of data saved in the machine's memory.

Drum Dot Print

Print the Drum Dot Check Sheet.

WLAN Report

Print the wireless LAN connection results.

Serial No.

-

Display the machine's serial number.

Firmware Version

Main Version

Check your machine's firmware version.

Sub3 Version

Security Ver.

Page Counter

Total

Check the total number of pages the machine has printed during its life.

Copy

Print

Other

Parts Life

Toner

View the approximate remaining toner life for each color.

Drum

Display the remaining life of each drum unit.

Belt

Display the remaining life of the belt unit.

Fuser

Display the remaining life of the fuser unit.

Secure Print

You can print data saved in the machine's memory when you enter your four-digit password.

Active only when the machine has secure print data.

Date & Time

Date & Time

Access the Date and Time setting menus.

Auto Daylight

Set the machine to change automatically for Daylight Saving Time.

Time Zone

Set your time zone.

Reset

Machine Reset

Restore all the machine settings that you have changed.

Network Reset

Restore all network settings back to the factory settings.

All Settings

Restore all the machine's settings back to the factory settings.

Factory Reset

Restore all the machine's settings to the factory defaults. Perform this operation when you dispose of your machine.

Local Language

(available for certain models)

-

Change your LCD language.