Home > Machine Settings > Change Machine Settings from the Control Panel > Settings and Features Tables > Settings Tables (2 Line LCD DCP models)
Settings Tables (2 Line LCD DCP models)
[General Setup]
[General Setup]
Level 3 | Level 4 | Level 5 | Descriptions |
---|---|---|---|
Tray Setting | Paper Type | - | Set the type of paper in the paper tray. |
Auto Switching | - | Enable if you want the machine to automatically select the paper size from the two sizes set in the Paper Size setting. | |
Paper Size | - | Set the paper size in the paper tray. When the Auto Switching setting is turned on, the machine automatically selects from the two sizes already set in the Paper Size setting. | |
Print Position | X Offset | Move the print start position (at the upper left corner of pages) horizontally from -500 (left) to +500 (right) dots in 300 dpi. | |
Y Offset | Move the print start position (at the upper left corner of pages) vertically from -500 (up) to +500 (down) dots in 300 dpi. | ||
Ecology | Eco Mode | - | |
Toner Save | - | Increase the page yield of the toner cartridge. | |
Auto Power Off | - | Set the number of minutes or hours before the machine enters Power Off mode. | |
LCD Contrast | - | - | Adjust the LCD contrast. |
Replace Toner | - | - | Set the machine to continue printing after the LCD displays Replace Toner. |
[Copy]
[Copy]
Level 3 | Level 4 | Descriptions |
---|---|---|
Density | - | Adjust the density. |
Quality | - | Choose the Copy resolution for your type of document. |
Contrast | - | Adjust the contrast for copies. |
ID Copy | Density | Adjust the density. |
Quality | Choose the Copy resolution for your type of document. | |
Contrast | Adjust the contrast for copies. | |
2in1/1in1 | Make 2 in 1 ID copies. |
[Printer]
[Printer]
Level 3 | Descriptions |
---|---|
Resolution | Select a print resolution. |
Density | Increase or decrease the print density. |
Test Print | Print a test page. |
Auto Continue | Select this setting if you want the machine to clear paper size errors or media type errors, and to use the paper in the tray. |
Print Position | Access the Print Position setting menus. |
Reset Printer | Restore the machine settings to the factory settings. |
[Network]
[Network]
Level 3 | Level 4 | Level 5 | Level 6 | Descriptions |
---|---|---|---|---|
Wired LAN | TCP/IP | Boot Method | - | Select the Boot method that best suits your needs. |
IP Address | - | Enter the IP address. | ||
Subnet Mask | - | Enter the Subnet mask. | ||
Gateway | - | Enter the Gateway address. | ||
Node Name | - | Enter the Node name. (Up to 32 characters) | ||
WINS Config | - | Select the WINS configuration mode. | ||
WINS Server | Primary | Specify the IP address of the primary WINS server. | ||
Secondary | Specify the IP address of the secondary WINS server. | |||
DNS Server | Primary | Specify the IP address of the primary DNS server. | ||
Secondary | Specify the IP address of the secondary DNS server. | |||
APIPA | - | Set the machine to allocate the IP address from the link-local address range automatically. | ||
IPv6 | - | Turn the IPv6 protocol on or off. | ||
Ethernet | - | - | Select the Ethernet link mode. | |
Wired Status | - | - | View the current wired status. | |
MAC Address | - | - | View the machine's MAC address. | |
Set to Default | - | - | Restore the wired network settings to the factory settings. | |
Wired Enable | - | - | Turn the Wired LAN interface on or off manually. | |
WLAN(Wi-Fi) | Find Network | - | - | Configure your wireless network settings manually. |
TCP/IP | Boot Method | - | Select the Boot method that best suits your needs. | |
IP Address | - | Enter the IP address. | ||
Subnet Mask | - | Enter the Subnet mask. | ||
Gateway | - | Enter the Gateway address. | ||
Node Name | - | Enter the Node name. (Up to 32 characters) | ||
WINS Config | - | Select the WINS configuration mode. | ||
WINS Server | Primary | Specify the IP address of the primary WINS server. | ||
Secondary | Specify the IP address of the secondary WINS server. | |||
DNS Server | Primary | Specify the IP address of the primary DNS server. | ||
Secondary | Specify the IP address of the secondary DNS server. | |||
APIPA | - | Set the machine to allocate the IP address from the link-local address range automatically. | ||
IPv6 | - | Turn the IPv6 protocol on or off. | ||
WPS/PushButton | - | - | Configure your wireless network settings using the one-button push method. | |
WPS/PIN Code | - | - | Configure your wireless network settings using WPS with a PIN. | |
Recover WLAN | - | - | Reset and restart your wireless network. | |
WLAN Status | Status | - | View the current wireless network status. | |
Signal | - | View the current wireless network signal strength. | ||
Channel | - | View the current wireless network channel. | ||
Speed | - | View the current wireless network speed. | ||
SSID | - | View the current SSID. | ||
Comm. Mode | - | View the current Communication mode. | ||
MAC Address | - | - | View the machine's MAC address. | |
Set to Default | - | - | Restore the wireless network settings to the factory settings. | |
WLAN Enable | - | - | Turn the WLAN on or off manually. | |
Wi-Fi Direct | Manual | - | - | Configure your Wi-Fi Direct network settings manually. |
Group Owner | - | - | Set your machine as the Group Owner. | |
Push Button | - | - | Configure your Wi-Fi Direct network settings using the one-button push method. | |
PIN Code | - | - | Configure your Wi-Fi Direct network settings using WPS with a PIN code. | |
Device Info. | Device Name | - | View your machine's device name. | |
SSID | - | View the Group Owner's SSID. When the machine is not connected, the LCD displays Not Connected. | ||
IP Address | - | View your machine's current IP Address. | ||
Status Info. | Status | - | View the current Wi-Fi Direct network status. | |
Signal | - | View the current Wi-Fi Direct network signal strength. When your machine acts as Group Owner, the LCD always indicates a strong signal. | ||
Channel | - | View the current Wi-Fi Direct network channel. | ||
Speed | - | View the current Wi-Fi Direct network speed. | ||
I/F Enable | - | - | Turn the Wi-Fi Direct connection on or off. | |
Web Based Mgmt | - | - | - | Enable or disable Web Based Management. If you enable this function, make sure you specify the connection method to use Web Based Management. |
Global Detect | Allow Detect | - | - | Enable or disable Global Detect, a function that detects and notifies the user when the user unintentionally connects to a global network. |
Reject Access | - | - | Disable connections to the global network. | |
Network Reset | - | - | - | Restore all network settings back to the factory settings. |
[Print Reports]
[Print Reports]
Level 3 | Descriptions |
---|---|
User Settings | Print a list of your User settings. |
Print Settings | Print a list of your Printer settings. |
Network Config | Print a list of your Network settings. |
WLAN Report | Print the wireless LAN connection results. |
[Machine Info.]
[Machine Info.]
Level 3 | Level 4 | Descriptions |
---|---|---|
Serial No. | - | Check your machine's serial number. |
Version | Main Version | Check your machine's firmware version. |
Security Ver. | ||
Page Counter | Total | Check the total number of pages the machine has printed during its life. |
Copy | ||
Other | ||
Parts Life | Toner | View the approximate remaining toner life. |
Drum | You can check the percentage of Drum life that remains available. | |
[Initial Setup]
[Initial Setup]
Level 3 | Level 4 | Descriptions |
---|---|---|
Reset | Machine Reset | Restore all the machine settings that you have changed. |
Network Reset | Restore all network settings back to the factory settings. | |
All Settings | Restore all the machine's settings back to the factory settings. | |
Factory Reset | Restore all the machine's settings to the factory defaults. Perform this operation when you dispose of your machine. | |
Local Language (available for certain models) | - | Change your LCD language. |