Search

Home > Network > Wireless Network Settings > Use the Wireless Network > Configure Your Machine for a Wireless Network When the SSID is Not Broadcast

Configure Your Machine for a Wireless Network When the SSID is Not Broadcast

DCP-T520W/DCP-T720DW/DCP-T725DW/DCP-T820DW

Before configuring your machine, we recommend writing down your wireless network settings. You will need this information before you continue with the configuration.

  1. Check and write down the current wireless network settings.
    Network Name (SSID)
      
    Communication Mode Authentication Method Encryption Mode Network Key
    Infrastructure Open System NONE -
    WEP
    Shared Key WEP
    WPA/WPA2-PSK AES
    TKIP

    For example:

    Network Name (SSID)
    HELLO
    Communication Mode Authentication Method Encryption Mode Network Key
    Infrastructure WPA2-PSK AES 12345678
    image
    If your router uses WEP encryption, enter the key used as the first WEP key. Your Brother machine supports the use of the first WEP key only.
  2. Press WiFi.
  3. Press image or image to select [Find Network]. Press OK.
  4. When the [WLAN Enable?] message appears, press image to select [On].
    This starts the wireless setup wizard. To cancel, press image.
  5. The machine will search for your network and display a list of available SSIDs. Press image or image to select the [<New SSID>] option, and then press OK.
  6. Enter the SSID name, and then press OK.
    image
    For more information about how to enter text, see Related Information.
  7. Press image or image to select the [Infrastructure] option. Press OK.
  8. Press image or image to select the Authentication Method. Press OK.
  9. Do one of the following:
    • If you selected the [Open System] option, press image or image to select the Encryption type [None] or [WEP], and then press OK.

      If you selected the [WEP] option for Encryption type, enter the WEP key, and then press OK.

    • If you selected the [Shared Key] option, enter the WEP key, and then press OK.
    • If you selected the [WPA/WPA2-PSK] option, press image or image to select the Encryption type [TKIP+AES] or [AES], and then press OK.

      Enter the WPA key, and then press OK.

    image
    • For more information about how to enter text, see Related Information.
    • Your Brother machine supports the use of the first WEP key only.
  10. To apply the settings, press image to select [Yes]. To cancel, press image to select [No].
  11. The machine attempts to connect to the wireless device you have selected.
If your wireless device is connected successfully, the machine's LCD displays [Connected].

You have completed the wireless network setup. To install the drivers and software necessary to use your machine, go to your model's Downloads page at support.brother.com.

(Windows) Or, use the Brother installation disc to set up your machine (not available in all countries).

MFC-T920DW

Before configuring your machine, we recommend writing down your wireless network settings. You will need this information before you continue with the configuration.

  1. Check and write down the current wireless network settings.
    Network Name (SSID)
      
    Communication Mode Authentication Method Encryption Mode Network Key
    Infrastructure Open System NONE -
    WEP
    Shared Key WEP
    WPA/WPA2-PSK AES
    TKIP

    For example:

    Network Name (SSID)
    HELLO
    Communication Mode Authentication Method Encryption Mode Network Key
    Infrastructure WPA2-PSK AES 12345678
    image
    If your router uses WEP encryption, enter the key used as the first WEP key. Your Brother machine supports the use of the first WEP key only.
  2. Press image.
  3. Press image or image to select the [Find Wi-Fi Network] option, and then press OK.
  4. When [Enable WLAN?] appears, press image.
    The wireless setup wizard starts. To cancel, press image.
  5. The machine will search for your network and display a list of available SSIDs. Press image or image to select the [<New SSID>] option, and then press OK.
  6. Enter the SSID name, and then press OK.
    image
    For more information about how to enter text, see Related Information.
  7. Select [Infrastructure], and then press OK.
  8. Select the Authentication Method, and then press OK.
  9. Do one of the following:
    • If you selected the [Open System] option, press image or image to select the Encryption type [None] or [WEP], and then press OK.

      If you selected the [WEP] option for Encryption type, enter the WEP key, and then press OK.

    • If you selected the [Shared Key] option, enter the WEP key, and then press OK.
    • If you selected the [WPA/WPA2-PSK] option, press image or image to select the Encryption type [TKIP+AES] or [AES], and then press OK.

      Enter the WPA key, and then press OK.

    image
    • For more information about how to enter text, see Related Information.
    • Your Brother machine supports the use of the first WEP key only.
  10. The machine attempts to connect to the wireless device you have selected.
If your wireless device is connected successfully, the machine's LCD displays [Connection successful.].

You have completed the wireless network setup. To install the drivers and software necessary to use your machine, go to your model's Downloads page at support.brother.com.

(Windows) Or, use the Brother installation disc to set up your machine (not available in all countries).

Did you find the information you needed?