Home > Printer Settings > Change Printer Settings Using the Printer > Settings Tables
Settings Tables
The Settings tables describe the menu selections and options.
Some settings may differ depending on the firmware (printer software) version.
[WLAN]
Level 1 | Level 2 | Descriptions |
|---|---|---|
On/Off | On / Off | Turn the WLAN function on or off. |
Mode | Direct / Infrastructure / Direct/Infra | Select the network mode when you set the WLAN function to on. |
WPS | Button Push / PIN Code | Select the WPS network settings method. |
WLANAssistant | Start / Back | Use the WLAN connection assistant function to configure your wireless network settings. |
IP Address | Display the IP Address. | |
[Bluetooth]
Level 1 | Level 2 | Descriptions |
|---|---|---|
On/Off | On / Off | Turn the Bluetooth function on or off. |
Mode | Classic & LE / Classic / Low Energy | Select the Bluetooth mode. |
AutoReconnect | On / Off | Switch to Automatic Reconnection mode (only for Apple devices: iPad, iPhone, or iPod touch). |
Clear History | Delete the information for auto re-paired devices registered in the printer. | |
BT Address | Display the Bluetooth address. | |
Print Barcode | Print the Bluetooth address and corresponding barcode. | |
[Wired LAN]
Level 1 | Level 2 | Descriptions |
|---|---|---|
Cradle LAN | On / Off | Select the wireless (infrastructure) or wired connection when the printer is placed on the Active Docking Station. |
IP Address | Display the IP Address. | |
[Media]
Level 1 | Level 2 | Descriptions |
|---|---|---|
Select Media | - | Select the paper size and paper type or check the current paper size setting. The list contains:
|
Auto Detect | - | Automatically adjust the sensor sensitivity and detect the length of the set paper. Specify Settings in advance. |
Settings *1 | - | Configure the settings before performing Auto Detect. |
Width | Select the paper width to be auto-detected. | |
Sensor Type | Select the sensor type: Die-cut, Mark, or Continuous. | |
Sensor Calibr | Enable or disable sensor calibration during auto-detection. | |
Media Timeout | Set the auto-detected paper to Continuous if Auto Detect does not find any gap or black mark according to the Media Timeout length. | |
Energy Rank | Select the energy rank to adjust the print density. |
*1
Requires from the firmware version 1.09 or later.
[Settings]
Level 1 | Level 2 | Descriptions |
|---|---|---|
Exit Position | Tear / Peeler | Select the media exit method. |
Language | Dansk / Deutsch / English / Español / Français / Italiano / Nederlands / Norsk / Português / Suomi / Svenska / 日本語 / 繁體中文 | Select the language. |
LCD Contrast | +2 / +1 / 0 / -1 / -2 | Set the contrast of the LCD. The higher the number, the stronger the contrast. |
Beeper | On / Off | Enable or disable the beeper. |
Configuration | Check the firmware version, font version, and available memory. | |
Tear Bar | Upward / Downward | Adjust the tear position. This setting appears when the Linerless is set to Off in the Advanced tab of the Printer Setting Tool. |
Cover Setting *1 | Select Media | Shows the Select Media screen for ten seconds after you close the Roll Compartment Cover. |
Feed | Feeds the label automatically when you close the Roll Compartment Cover. | |
Auto Detect | Performs Auto Detect automatically when you close the Roll Compartment Cover. The printer displays the detected paper size, and then displays the Ready screen. | |
None | No action and no change on the LCD. | |
Clock | On / Off | Show or hide the clock icon on the LCD. |
AutoSync Time | On / Off | This setting appears when Clock is set to On. |
Time Zone | Set the time zone. This setting appears when Clock is set to On. | |
Date&Time | Display the date and time. This setting appears when Clock is set to On. | |
*1
Requires from the firmware version 1.09 or later.
Did you find the information you needed?