Preguntas frecuentes y solución de problemas



Preguntas frecuentes y solución de problemas

Preguntas frecuentes y solución de problemas

Fecha: 22/10/2015 ID: faqh00000712_001

Adjusting the Blade Extension

The appropriate blade extension differs depending on the material type and thickness. Before installing the holder in the carriage, turn the holder cap to adjust the blade extension, and then perform trial cutting.



Cutting Settings


Use the following table to select the appropriate settings according to the material that will be cut.


Material and its thickness

Blade scale setting

Cut pressure setting

Cutting blade
Standard cut blade


Deep cut blade



Printer paper

80 g/m²
(0.1 mm)

3 -1 -

Scrapbook paper

120 g/m²
(0.15 mm)

3.5 0 -
Scrapbook paper
200 g/m²
(0.25 mm)
4 0 -
Cardstock (thin) 200 g/m²
(0.25 mm)
4 0 -


280 g/m²
(0.35 mm)

5 0 -
Vellum, tracing paper 0.07 mm 3 0 -
Poster board (thin) 280 g/m²
(0.35 mm)
5.5 0 -
Poster board (thick) 400 g/m²
(0.5 mm)
7.5 4 -

Thin cotton fabric

(for quilt piece)

0.25 mm 4 4 -

Thin cotton fabric
for quilt piece)

0.25 mm 4 4 -

Flannel (for quilt piece)

0.6 mm

6.5 4 -

(except for quilt piece)

0.6 mm

6.5 4 -


1 mm

5 5 -

Denim 14 oz

0.75 mm 5.5 6 -
Others Plastic sheet (PP) 0.2 mm 4 0 -


0.2 mm

4 0 -
Magnet 0.3 mm 5.5 0 -

Sticker or seal

0.2 mm 4 0 -


* Adjust the setting for “Cut Pressure” in the settings screen. For details, see "Settings for Specific Functions".
* Use a high tack adhesive fabric support sheet or a iron-on fabric appliqué contact sheet when you cut a piece of fabric out.
For details, see "Mat and Material Combinations".


The settings indicated in the table are approximations. The setting will differ depending on the type and thickness of the material to be cut. Be sure to perform a trial cutting first.



Appropriate Blade Extension


Adjust the blade extension to slightly exceed the thickness of the material that will be cut. Use the markings on the holder to make the adjustment.

img (1) End of holder cap
(2) Material that will be cut
(3) Length of blade tip

Be careful that the blade does not extend too much. The blade can cut even though it only slightly extends from the holder. If too much of the blade extends, it may break.



Adjusting the Cutting Blade


  1. Remove the protective cap.

    After use, be sure to retract the blade into the holder and attach the protective cap.




    Do not allow infants/children to put the protective caps in their mouths.


  2. With the reference line on the holder facing toward you, fully turn the cap to the right to extend the blade tip to its maximum.
    img (1) Reference line
    (2) Extend the blade tip to its maximum.
  3. Check the thickness of the material, and then adjust the blade extension. See “Cutting Settings”
    img (1) Turn to the left to decrease the blade extension.
    (2) Turn to the right to increase the blade extension.


Preguntas frecuentes relacionadas

Modelos relacionados

CM350e, CM650W

Si necesita asistencia, contáctese con el servicio al cliente de Brother:

Comentarios sobre el contenido

Para ayudarnos a mejorar el soporte, bríndenos sus comentarios a continuación.
Paso 1: ¿Cómo lo ayudó la información en esta página?
Paso 2: ¿Quiere agregar otros comentarios?

Observe que este formulario solo se utiliza para comentarios.