When tansferring an embroidery data from PE-DESIGN 11 to the embroidery machine connected to the computer with a USB cable, the message "Disk full while accessing [filename]." appears.

"There is no needle plate cover. Attach a needle plate cover." message appears on the LCD. What does it mean?

"Set the clock." message appears on the LCD. What does it mean?

"The upper thread may not be threaded correctly. Thread the upper thread from the beginning." message appears on the LCD. What does it mean?

"This USB media is incompatible." message appears on the LCD. What does it mean?

"This USB media cannot be used." message appears on the LCD. What does it mean?

"USB media is not loaded. Load USB media." message appears on the LCD. What does it mean?

"This key does not operate when the needle is down. Raise the needle and press the key again." message appears on the LCD. What does it mean?

"Use the presser foot lifter button to lower the presser foot." message appears on the LCD. What does it mean?

Upper threading (Point)

When thread got tangled.

"This file cannot be used." message appears on the LCD. What does it mean?

When I create an embroidery pattern design on PE-DESIGN(PE-DESIGN, PE-DESIGN Lite, or PED-Basic), what Design Page Size is my sewing machine?

"This function cannot be used while in the sensor mode." message appears on the LCD. What does it mean?

"This file exceeds the data capacity and cannot be used. Use a suitable size file." message appears on the LCD. What does it mean?

"The shutoff support mode has been activated. Turn off the machine." message appears on the LCD. What does it mean?

"The safety device has been activated. Is the thread tangled? Is the needle bent?" message appears on the LCD. What does it mean?

"The pattern field extends out of the pattern area, repeat setting the position and angle using the sensor pen." message appears on the LCD. What does it mean?

"The needle will move. Keep your hands etc. away from the needle area." message appears on the LCD. What does it mean?

"Sensor module error." message appears on the LCD. What does it mean?

"OK to revert to the original position and/or angle?" message appears on the LCD. What does it mean?

"OK to reset the pattern’s border setting, position and/or angle?" message appears on the LCD. What does it mean?

"OK to recall and resume previous memory?" message appears on the LCD. What does it mean?

"OK to delete the selected pattern?" message appears on the LCD. What does it mean?

"Move the sensor pen away from the currently marked position." message appears on the LCD. What does it mean?

"Failed to save file." message appears on the LCD. What does it mean?

"OK to automatically lower the presser foot?" message appears on the LCD. What does it mean?

"Turn off the power and replace the needle plate." message appears on the LCD. What does it mean?

"A malfunction occurred. Turn the machine off, then on again." message appears on the LCD. What does it mean?

"Lower the presser foot lever." message appears on the LCD. What does it mean?

"The pockets are full. Delete a pattern." message appears on the LCD. What does it mean?

"Transmitting by USB" message appears on the LCD. What does it mean?

"USB media error" message appears on the LCD. What does it mean?

"The USB media was changed. Do not change the USB media while it is being read." message appears on the LCD. What does it mean?

"Retrieving the pattern. Wait a moment." message appears on the LCD. What does it mean?

"Not enough available memory to save the pattern. Delete another pattern?" message appears on the LCD. What does it mean?

"The carriage of the embroidery unit will move. Keep your hands etc. away from the carriage." message appears on the LCD. What does it mean?

"The bobbin thread is almost empty." message appears on the LCD. What does it mean?

"The bobbin winder safety device has activated. Is the thread tangled?" message appears on the LCD. What does it mean?

"Attach the embroidery frame." message appears on the LCD. What does it mean?

"Data volume is too large for this pattern." message appears on the LCD. What does it mean?

How to use the Multi-purpose Screwdriver. [ Position “3” ]

How to use the Multi-purpose Screwdriver. [ Position “2” ]

How to use the Multi-purpose Screwdriver. [ Position “1” ]

Why does the lower thread keep breaking?

How do I attach or remove the embroidery frame ?

How do I change the needle ?

How do I thread my machine ?

How do I set the bobbin ?