FAQs & Troubleshooting
![]() |
Popular |
68 Results
- 1How to use the Multi-purpose Screwdriver. [ Position “2” ]
- 2How to use the Multi-purpose Screwdriver. [ Position “1” ]
- 3Where do I put the oil in my machine?
- 4How do I set the bobbin ?
- 5How to use the Multi-purpose Screwdriver.
- 6How to use the Multi-purpose Screwdriver. [ Position “3” ]
- 7"OK to recall and resume previous memory?" message appears on the LCD. What does it mean?
- 8How do I calibrate the sensor pen?
- 9When tansferring an embroidery data from PE-DESIGN 11 to the embroidery machine connected to the computer with a USB cable, the message "Disk full while accessing [filename]." appears.
- 10"Failed to save file." message appears on the LCD. What does it mean?
- 11How do I thread my machine ?
- 12"The USB media was changed. Do not change the USB media while it is being read." message appears on the LCD. What does it mean?
- 13Why is the outline sewing off the pattern?
- 14Fabrics and stabilizer material for embroidery
- 15Embroidery
- 16"This file cannot be used." message appears on the LCD. What does it mean?
- 17"Set the clock." message appears on the LCD. What does it mean?
- 18"The upper thread may not be threaded correctly. Thread the upper thread from the beginning." message appears on the LCD. What does it mean?
- 19Why does the lower thread keep breaking?
- 20"This function cannot be used while in the sensor mode." message appears on the LCD. What does it mean?
- 21"There is no needle plate cover. Attach a needle plate cover." message appears on the LCD. What does it mean?
- 22"The pattern field extends out of the pattern area, repeat setting the position and angle using the sensor pen." message appears on the LCD. What does it mean?
- 23"OK to automatically lower the presser foot?" message appears on the LCD. What does it mean?
- 24When I sew an embroidery pattern design exported as DST format in PE-DESIGN, how do I specify whether or not the jump stitches are cut on the embroidery machine of the Innov-is series?
- 25How do I clean the race?
- 26How do I adjust an alternate bobbin case(with pink marking or no marking) using an embroidery pattern?
- 27When thread got tangled.
- 28"Move the sensor pen away from the currently marked position." message appears on the LCD. What does it mean?
- 29How do I attach or remove the Embroidery Unit?
- 30How do I change the needle ?
- 31"This USB media is incompatible." message appears on the LCD. What does it mean?
- 32"This USB media cannot be used." message appears on the LCD. What does it mean?
- 33"The bobbin thread is almost empty." message appears on the LCD. What does it mean?
- 34If the thread breaks during sewing.
- 35"This file exceeds the data capacity and cannot be used. Use a suitable size file." message appears on the LCD. What does it mean?
- 36"The needle will move. Keep your hands etc. away from the needle area." message appears on the LCD. What does it mean?
- 37"OK to delete the selected pattern?" message appears on the LCD. What does it mean?
- 38How do I specify the embroidering location with the sensor pen? (Specifying the embroidery pattern location by selecting the pattern center with the sensor pen.)
- 39How do I attach or remove the embroidery frame ?
- 40How do I wind the bobbin?
- 41"Lower the presser foot lever." message appears on the LCD. What does it mean?
- 42"USB media is not loaded. Load USB media." message appears on the LCD. What does it mean?
- 43"Retrieving the pattern. Wait a moment." message appears on the LCD. What does it mean?
- 44"Attach the embroidery frame." message appears on the LCD. What does it mean?
- 45"Data volume is too large for this pattern." message appears on the LCD. What does it mean?
- 46"Preventive maintenance is recommended" appears on the LCD.
- 47Upper threading (Point)
- 48"The safety device has been activated. Is the thread tangled? Is the needle bent?" message appears on the LCD. What does it mean?
- 49How do I specify the embroidering location with the sensor pen?(Specifying the embroidery pattern location by selecting the pattern edge with the sensor pen.)
- 50"The shutoff support mode has been activated. Turn off the machine." message appears on the LCD. What does it mean?