FAQs & Troubleshooting
![]() |
Popular |
108 Results
- 1How to use the Multi-purpose Screwdriver.
- 2How to use the Multi-purpose Screwdriver. [ Position “3” ]
- 3When I create an embroidery pattern design on PE-DESIGN(PE-DESIGN, PE-DESIGN Lite, or PED-Basic), what Design Page Size is my sewing machine?
- 4Combination of fabric, thread and needle
- 5How do I sew hook-and-loop fasteners(hook-and-loop tapes)?
- 6Why does the lower thread keep breaking?
- 7When thread got tangled.
- 8Fabric and Thread
- 9The bobbin thread cannot be pulled up.
- 10How do I set the bobbin ?
- 11"The bobbin winder safety device has activated. Is the thread tangled?" message appears on the LCD. What does it mean?
- 12How do I clean the race?
- 13How do I sew a blind hem?
- 14How do I specify the sewing end point with the sensor pen for utility stitches/ character decorative stitches?
- 15How do I specify the sewing end point with the sensor pen for utility stitches?
- 16"This pattern cannot be sewn with this mode." message appears on the LCD. What does it mean?
- 17"This key cannot be used at this time." message appears on the LCD. What does it mean?
- 18"This file exceeds the data capacity and cannot be used. Use a suitable size file." message appears on the LCD. What does it mean?
- 19"This file cannot be used." message appears on the LCD. What does it mean?
- 20"The shutoff support mode has been activated. Turn off the machine." message appears on the LCD. What does it mean?
- 21"The needle position cannot be changed for this stitch." message appears on the LCD. What does it mean?
- 22"The ending point cannot be selected for this stitch." message appears on the LCD. What does it mean?
- 23"Remove Embroidery foot with LED pointer from the machine." message appears on the LCD. What does it mean?
- 24"OK to reset the pattern’s border setting, position and/or angle?" message appears on the LCD. What does it mean?
- 25"OK to delete the setting?" message appears on the LCD. What does it mean?
- 26"Move the sensor pen away from the currently marked position." message appears on the LCD. What does it mean?
- 27"Failed to save file." message appears on the LCD. What does it mean?
- 28"An invalid sewing area was touched by the sensor pen. Touch again within the valid sewing area." message appears on the LCD. What does it mean?
- 29How do I specify the embroidering location with the sensor pen? (Specifying the embroidery pattern location by selecting the pattern center with the sensor pen.)
- 30How to specify the Guideline Marker Position With the Sensor Pen
- 31About Sensor Function Area
- 32How do I calibrate the sensor pen?
- 33How do I attach or remove the Embroidery Unit?
- 34How do I attach the Embroidery foot “W+” with LED pointer or “W”?
- 35How do I adjust the clock on the display?
- 36How do I remove or attach the presser foot ?
- 37How do I thread my machine ?
- 38"In twin needle mode, the automatic needle threading button cannot be used." message appears on the LCD. What does it mean?
- 39"OK to automatically lower the presser foot?" message appears on the LCD. What does it mean?
- 40"The carriage of the embroidery unit will move. Keep your hands etc. away from the carriage." message appears on the LCD. What does it mean?
- 41"The "Start/Stop" button does not operate with the foot controller attached. Remove the foot controller." appears on the LCD.
- 42"Use the presser foot lifter button to lower the presser foot." message appears on the LCD. What does it mean?
- 43The thread tension is incorrect.
- 44How do I sew buttonholes?
- 45How do I sew hook-and-loop fasteners(hook-and-loop tapes)?
- 46When tansferring an embroidery data from PE-DESIGN 11 to the embroidery machine connected to the computer with a USB cable, the message "Disk full while accessing [filename]." appears.
- 47The machine does not make stitches
- 48How to use the Multi-purpose Screwdriver. [ Position “2” ]
- 49How to use the Multi-purpose Screwdriver. [ Position “1” ]
- 50How do I remove or attach the presser foot holder?