FAQs & Troubleshooting
![]() |
Popular |
108 Results
- 1How do I sew hook-and-loop fasteners(hook-and-loop tapes)?
- 2Where do I put the oil in my machine?
- 3How do I adjust an alternate bobbin case(with pink marking or no marking) using an embroidery pattern?
- 4"Move the sensor pen away from the currently marked position." message appears on the LCD. What does it mean?
- 5When tansferring an embroidery data from PE-DESIGN 11 to the embroidery machine connected to the computer with a USB cable, the message "Disk full while accessing [filename]." appears.
- 6"The safety device has been activated. Is the thread tangled? Is the needle bent?" message appears on the LCD. What does it mean?
- 7"Raise the buttonhole lever." message appears on the LCD. What does it mean?
- 8If the thread breaks during sewing.
- 9"This function cannot be used while in the sensor mode." message appears on the LCD. What does it mean?
- 10"The pattern field extends out of the pattern area, repeat setting the position and angle using the sensor pen." message appears on the LCD. What does it mean?
- 11"The needle position cannot be changed for this stitch." message appears on the LCD. What does it mean?
- 12"OK to recall and resume previous memory?" message appears on the LCD. What does it mean?
- 13"A malfunction occurred. Turn the machine off, then on again." message appears on the LCD. What does it mean?
- 14"This USB media cannot be used." message appears on the LCD. What does it mean?
- 15The thread tension is incorrect.
- 16How do I sew an applique?
- 17Upper threading (Point)
- 18The bobbin thread cannot be pulled up.
- 19The machine does not make stitches
- 20How to use the Multi-purpose Screwdriver. [ Position “3” ]
- 21How to use the Multi-purpose Screwdriver. [ Position “2” ]
- 22How to use the Multi-purpose Screwdriver. [ Position “1” ]
- 23How to use the Multi-purpose Screwdriver.
- 24How do I remove or attach the presser foot holder?
- 25For better results when sewing stretch fabrics
- 26How do I specify the embroidering location with the sensor pen?(Specifying the embroidery pattern location by selecting the pattern edge with the sensor pen.)
- 27How do I specify the sewing end point with the sensor pen for utility stitches/ character decorative stitches?
- 28How do I specify the sewing end point with the sensor pen for utility stitches?
- 29"This stitch is not "Dual Feed Mode" compatible." message appears on the LCD. What does it mean?
- 30"This pattern cannot be sewn with this mode." message appears on the LCD. What does it mean?
- 31"This key cannot be used at this time." message appears on the LCD. What does it mean?
- 32"This file exceeds the data capacity and cannot be used. Use a suitable size file." message appears on the LCD. What does it mean?
- 33"This file cannot be used." message appears on the LCD. What does it mean?
- 34"There is no needle plate cover. Attach a needle plate cover." message appears on the LCD. What does it mean?
- 35"The shutoff support mode has been activated. Turn off the machine." message appears on the LCD. What does it mean?
- 36"The needle will move. Keep your hands etc. away from the needle area." message appears on the LCD. What does it mean?
- 37"The ending point cannot be selected for this stitch." message appears on the LCD. What does it mean?
- 38"Set the clock." message appears on the LCD. What does it mean?
- 39"Sensor module error." message appears on the LCD. What does it mean?
- 40"Remove Embroidery foot with LED pointer from the machine." message appears on the LCD. What does it mean?
- 41"Remove Dual Feed module from the machine." message appears on the LCD. What does it mean?
- 42"OK to revert to the original position and/or angle?" message appears on the LCD. What does it mean?
- 43"OK to reset the pattern’s border setting, position and/or angle?" message appears on the LCD. What does it mean?
- 44"OK to delete the setting?" message appears on the LCD. What does it mean?
- 45"OK to delete the selected pattern?" message appears on the LCD. What does it mean?
- 46"OK to delete the ending point setting?" message appears on the LCD. What does it mean?
- 47"Failed to save file." message appears on the LCD. What does it mean?
- 48"An invalid area was touched by the sensor pen. Touch again within the valid sewing area." message appears on the LCD. What does it mean?
- 49How do I change the volume of operation sounds or alarm sounds?
- 50"An invalid sewing area was touched by the sensor pen. Touch again within the valid sewing area." message appears on the LCD. What does it mean?