Search

Home > Network > Wireless Network Settings > Use the Wireless Network > Configure Your Machine for an Enterprise Wireless Network

Configure Your Machine for an Enterprise Wireless Network

Before configuring your machine, we recommend writing down your wireless network settings. You will need this information before you continue with the configuration.

  1. Check and record the current wireless network settings.
    Network Name (SSID)
     
    Authentication Method Encryption Mode User ID Password
    EAP-FAST/NONE AES
    TKIP
    EAP-FAST/MS-CHAPv2 AES
    TKIP
    EAP-FAST/GTC AES
    TKIP
    PEAP/MS-CHAPv2 AES
    TKIP
    PEAP/GTC AES
    TKIP
    EAP-TTLS/CHAP AES
    TKIP
    EAP-TTLS/MS-CHAP AES
    TKIP
    EAP-TTLS/MS-CHAPv2 AES
    TKIP
    EAP-TTLS/PAP AES
    TKIP
    EAP-TLS AES -
    TKIP -

    For example:

    Network Name (SSID)
    HELLO
    Authentication Method Encryption Mode User ID Password
    EAP-FAST/MS-CHAPv2 AES Brother 12345678
    image
    • If you configure your machine using EAP-TLS authentication, you must install the client certificate issued by a CA before you start configuration. Contact your network administrator about the client certificate. If you have installed more than one certificate, we recommend writing down the certificate name you want to use.

    • If you verify your machine using the common name of the server certificate, we recommend writing down the common name before you start configuration. Contact your network administrator about the common name of the server certificate.

  2. Press image [Settings]>[All Settings]>[Network]>[WLAN(Wi-Fi)]>[Find Wi-Fi Network].
  3. When [Enable WLAN?] appears, press [Yes].
    This will start the wireless setup wizard. To cancel, press [No].
  4. The machine will search for your network and display a list of available SSIDs. Press image or image to display the [<New SSID>] option.
  5. Press [<New SSID>], and then press [OK].
  6. Enter the SSID name, and then press [OK].
  7. Select the Authentication Method.
  8. Do one of the following:
    • If you selected the [EAP-FAST], [PEAP] or [EAP-TTLS] option, press image or image to select the Inner Authentication Method [NONE], [CHAP], [MS-CHAP], [MS-CHAPv2], [GTC] or [PAP].
      image
      Depending on your Authentication Method, the Inner Authentication Method selections may differ.

      Select the Encryption Type [TKIP+AES] or [AES].

      Select the Verification Method [No Verification], [CA] or [CA + Server ID].

      • If you selected the [CA + Server ID] option, enter the server ID, user ID, and password (if required), and then press [OK] for each option.
      • For other selections, enter the user ID and Password, and then press [OK] for each option.
      image
      If you have not imported a CA certificate into your machine, the machine displays [No Verification].
    • If you selected the [EAP-TTLS] option, select the Encryption Type [TKIP+AES] or [AES].

      When the machine displays a list of available Client Certificates, select the certificate you want.

      Select the Verification Method [No Verification], [CA] or [CA + Server ID].

      • If you selected the [CA + Server ID] option, enter the server ID and user ID, and then press [OK] for each option.
      • For other selections, enter the user ID, and then press [OK].
  9. The machine attempts to connect to the wireless device you have selected.
If your wireless device is connected successfully, the machine's LCD displays [Connected]. Press [OK].

You have completed the wireless network setup. To install the drivers or the application necessary for operating your machine, go to your model's Downloads page at support.brother.com/downloads.

Did you find the information you needed?