Safety precautions

To use the printer safely

If you DO NOT follow these safety instructions, there is a possibility of a fire, electrical shock, burn or suffocation. Please keep these instructions for later reference and read them before attempting any maintenance.
WARNING WARNING
Graphic
There are high voltage electrodes inside the printer. Before you clean the inside of the printer or replace parts, make sure that you have turned off the power switch and unplugged the printer from the AC power outlet.
Graphic
Graphic
DO NOT handle the plug with wet hands. Doing this might cause an electrical shock.
Graphic
Always make sure the plug is fully inserted.
This product must be installed near an AC power outlet that is easily accessible. In case of an emergency, you must disconnect the power cord from the AC power outlet to shut off the power completely.
Lightning and power surges can damage this product! We recommend that you use a quality surge protection device on the AC power outlet, or unplug the cords during a lightning storm.
Use the printer within the recommended power range.
Power source:
AC 220 to 240 V, 50/60 Hz
The power cord, including extensions, should be no longer than 5 meters (16.5 feet).
Do not share the same power circuit with other high-powered appliances, such as an air conditioner, copier, shredder and so on. If you cannot avoid using the printer with these appliances, we recommend that you use a voltage transformer or a high-frequency noise filter.
Use a voltage regulator if the power source is not stable.
Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.
Use only the power cord provided with the machine.
Plastic bags are used in the packaging. To avoid danger of suffocation, keep these bags away from babies and children.
DO NOT use flammable substances, any type of spray or any organic solvent/liquids contains alcohol or ammonia to clean the inside or outside of the machine. Doing this may cause a fire or electrical shock. Refer to Cleaning for how to clean the machine.
Graphic
DO NOT use a vacuum cleaner to clean up scattered toner. Doing this might cause the toner dust to ignite inside the vacuum cleaner, potentially starting a fire. Carefully clean the toner dust with a dry, lint-free cloth and dispose of it according to local regulations.
Cleaning the outside of the printer:
Make sure that you have unplugged the printer from the AC power outlet.
Use neutral detergents. Cleaning with volatile liquids such as thinner or benzine will damage the outside surface of the printer.
DO NOT use cleaning materials that contain ammonia.
This printer is heavy and weighs approximately 19.0 kg (41.9 lb). To prevent injuries when moving or lifting this printer, make sure to use at least two people. Be careful not to pinch your fingers when you set the printer back down.
Graphic
CAUTION CAUTION
Graphic
After you have just used the printer, some internal parts of the printer will be extremely hot. When you open the top or back cover (back output tray) of the printer, DO NOT touch the shaded parts shown in the illustration.
Graphic
Inside the printer
(Top View)
Graphic
Inside the printer
(Back View)
Put your printer on a flat, stable surface such as a desk that is free of vibration and shocks.
Only use the printer within the following ranges of temperature and humidity:
Temperature: 10 °C to 32.5 °C (50 °F to 90.5 °F)
Humidity: 20% to 80% (without condensation)
Use the printer in a well-ventilated room.
Avoid placing your machine in a high-traffic area.
DO NOT put the printer where the ventilation hole of the printer is blocked. Keep a gap of roughly 100 mm (4 in.) between the ventilation hole and the wall.
DO NOT place the machine near heaters, air conditioners, refrigerators, water, chemicals or devices that contain magnets or generate magnetic fields.
DO NOT expose the machine to direct sunlight, excessive heat, open/naked flames, salty or corrosive gasses, moisture, or dust.
DO NOT put the printer near devices that contain magnets or produce magnetic fields.
DO NOT connect your machine to an AC power outlet controlled by wall switches or automatic timers.
DO NOT connect your machine to an AC power outlet on the same circuit as large appliances or other equipment that might disrupt the power supply.
DO NOT put the printer near heaters, air conditioners, chemicals or refrigerators.
DO NOT put objects on top of the machine.
CAUTION IMPORTANT
DO NOT remove or damage the caution labels located on or around the fuser.
Graphic
Note Note
Keep a minimum gap around the printer as shown in the illustration.
Graphic