Home > Machine Settings > Change Machine Settings from the Control Panel > Settings and Features Tables > Settings Tables (2 Line LCD DCP models)
Settings Tables (2 Line LCD DCP models)
[General Setup]
Level 1 | Level 2 | Level 3 | Descriptions |
|---|---|---|---|
Tray Setting | Paper Type | - | Set the type of paper in the paper tray. |
Paper Size | - | Set the size of paper in the paper tray. | |
Check Size | - | Select whether to display a message telling you to check that the size and type of the paper in the machine and the machine's Paper Size and Paper Type settings match. | |
Ecology | Eco Mode | - | Turn on the following machine settings at the same time.
|
Toner Save | - | Increase the page yield of the toner cartridge. | |
Sleep Time | - | Set the number of minutes before the machine enters Sleep mode. | |
Quiet Mode | - | Decrease printing noise. | |
Auto Power Off | - | Set the number of hours that the machine will remain in Deep Sleep mode before going into Power Off mode. | |
LCD Contrast | - | - | Adjust the LCD contrast. |
Replace Toner | - | - | Set the machine to continue printing after the LCD displays Replace Toner. |
[Copy]
Level 1 | Level 2 | Descriptions |
|---|---|---|
Density | - | Adjust the density. |
Quality | - | Choose the Copy resolution for your type of document. |
Contrast | - | Adjust the contrast for copies. |
ID Copy | Density | Adjust the density. |
Quality | Choose the Copy resolution for your type of document. | |
Contrast | Adjust the contrast for copies. | |
2in1/1in1 | Make 2 in 1 ID copies. |
[Printer]
For Printer Emulation Supported models
Level 1 | Level 2 | Level 3 | Descriptions |
|---|---|---|---|
Emulation | - | - | Set the printer emulation mode. |
Print Options | Font List | HP LaserJet | Print a list of the machine’s internal fonts. |
BR-Script 3 | |||
Test Print | - | Print a test page. | |
2-sided | 2-sided Print | - | Turn 2-sided printing off or on and select flip on long edge or short edge. |
Single Image | For a print job where the last page is a 1-sided image, select the 1-sided Feed option to reduce printing time. | ||
Auto Continue | - | - | Select this setting if you want the machine to clear paper size errors, and to use the paper in the tray. |
Tray Command | - | - | Select this setting if a tray mismatch appears when you use the HP drivers. |
Reset Printer | - | - | Restore the printer settings to the factory settings. |
For the Other models
Level 1 | Descriptions |
|---|---|
Test Print | Print a test page. |
2-sided | Turn 2-sided printing off or on and select flip on long edge or short edge. |
Auto Continue | Select this setting if you want the machine to clear paper size errors, and to use the paper in the tray. |
Reset Printer | Restore the printer settings to the factory settings. |
[Network]
For wired and wireless network models
Level 1 | Level 2 | Level 3 | Level 4 | Descriptions |
|---|---|---|---|---|
Wired LAN | TCP/IP | Boot Method | - | Select the Boot method that best suits your needs. |
IP Address | - | Enter the IP address. | ||
Subnet Mask | - | Enter the Subnet mask. | ||
Gateway | - | Enter the Gateway address. | ||
Node Name | - | Enter the Node name. (Up to 32 characters) | ||
WINS Config | - | Select the WINS configuration mode. | ||
WINS Server | Primary | Specify the IP address of the primary WINS server. | ||
Secondary | Specify the IP address of the secondary WINS server. | |||
DNS Server | Primary | Specify the IP address of the primary DNS server. | ||
Secondary | Specify the IP address of the secondary DNS server. | |||
APIPA | - | Set the machine to allocate the IP address from the link-local address range automatically. | ||
IPv6 | - | Turn the IPv6 protocol on or off. For more detailed information, go to your model's FAQs & Troubleshooting page on the Brother support website at support.brother.com. | ||
Ethernet | - | - | Select the Ethernet link mode. | |
Wired Status | - | - | View the current wired status. | |
MAC Address | - | - | View the machine's MAC address. | |
Set to Default | - | - | Restore the wired network settings to the factory settings. | |
Wired Enable | - | - | Turn the Wired LAN interface on or off manually. | |
WLAN | TCP/IP | Boot Method | - | Select the Boot method that best suits your needs. |
IP Address | - | Enter the IP address. | ||
Subnet Mask | - | Enter the Subnet mask. | ||
Gateway | - | Enter the Gateway address. | ||
Node Name | - | Enter the Node name. (Up to 32 characters) | ||
WINS Config | - | Select the WINS configuration mode. | ||
WINS Server | Primary | Specify the IP address of the primary WINS server. | ||
Secondary | Specify the IP address of the secondary WINS server. | |||
DNS Server | Primary | Specify the IP address of the primary DNS server. | ||
Secondary | Specify the IP address of the secondary DNS server. | |||
APIPA | - | Set the machine to allocate the IP address from the link-local address range automatically. | ||
IPv6 | - | Turn the IPv6 protocol on or off. For more detailed information, go to your model's FAQs & Troubleshooting page on the Brother support website at support.brother.com. | ||
Setup Wizard | - | - | Configure your wireless network settings manually. | |
WLAN Assistant | - | - | Configure your wireless network settings using the Brother installation disc. | |
WPS | - | - | Configure your wireless network settings using the one-button push method. | |
WPS w/PIN Code | - | - | Configure your wireless network settings using WPS with a PIN. | |
WLAN Status | Status | - | View the current wireless network status. | |
Signal | - | View the current wireless network signal strength. | ||
Channel | - | View the current wireless network channel. | ||
Speed | - | View the current wireless network speed. | ||
SSID | - | View the current SSID. | ||
Comm. Mode | - | View the current Communication mode. | ||
MAC Address | - | - | View the machine's MAC address. | |
Set to Default | - | - | Restore the wireless network settings to the factory settings. | |
WLAN Enable | - | - | Turn the WLAN on or off manually. | |
Wi-Fi Direct | Push Button | - | - | Configure your Wi-Fi Direct network settings using the one-button push method. |
PIN Code | - | - | Configure your Wi-Fi Direct network settings using WPS with a PIN code. | |
Manual | - | - | Configure your Wi-Fi Direct network settings manually. | |
Group Owner | - | - | Set your machine as the Group Owner. | |
Device Info. | Device Name | - | View your machine's device name. | |
SSID | - | View the Group Owner's SSID. When the machine is not connected, the LCD displays Not Connected. | ||
IP Address | - | View your machine's current IP Address. | ||
Status Info. | Status | - | View the current Wi-Fi Direct network status. | |
Signal | - | View the current Wi-Fi Direct network signal strength. When your machine acts as Group Owner, the LCD always indicates a strong signal. | ||
Channel | - | View the current Wi-Fi Direct network channel. | ||
Speed | - | View the current Wi-Fi Direct network speed. | ||
I/F Enable | - | - | Turn the Wi-Fi Direct connection on or off. | |
Network Reset | - | - | - | Restore all network settings back to the factory settings. |
For wireless network models
Level 1 | Level 2 | Level 3 | Level 4 | Descriptions |
|---|---|---|---|---|
WLAN | TCP/IP | Boot Method | - | Select the Boot method that best suits your needs. |
IP Address | - | Enter the IP address. | ||
Subnet Mask | - | Enter the Subnet mask. | ||
Gateway | - | Enter the Gateway address. | ||
Node Name | - | Enter the Node name. (Up to 32 characters) | ||
WINS Config | - | Select the WINS configuration mode. | ||
WINS Server | Primary | Specify the IP address of the primary WINS server. | ||
Secondary | Specify the IP address of the secondary WINS server. | |||
DNS Server | Primary | Specify the IP address of the primary DNS server. | ||
Secondary | Specify the IP address of the secondary DNS server. | |||
APIPA | - | Set the machine to allocate the IP address from the link-local address range automatically. | ||
IPv6 | - | Turn the IPv6 protocol on or off. For more detailed information, go to your model's FAQs & Troubleshooting page on the Brother support website at support.brother.com. | ||
Setup Wizard | - | - | Configure your wireless network settings manually. | |
WLAN Assistant | - | - | Configure your wireless network settings using the Brother installation disc. | |
WPS | - | - | Configure your wireless network settings using the one-button push method. | |
WPS w/PIN Code | - | - | Configure your wireless network settings using WPS with a PIN. | |
WLAN Status | Status | - | View the current wireless network status. | |
Signal | - | View the current wireless network signal strength. | ||
Channel | - | View the current wireless network channel. | ||
Speed | - | View the current wireless network speed. | ||
SSID | - | View the current SSID. | ||
Comm. Mode | - | View the current Communication mode. | ||
MAC Address | - | - | View the machine's MAC address. | |
WLAN Enable | - | - | Turn the WLAN on or off manually. | |
Wi-Fi Direct | Push Button | - | - | Configure your Wi-Fi Direct network settings using the one-button push method. |
PIN Code | - | - | Configure your Wi-Fi Direct network settings using WPS with a PIN code. | |
Manual | - | - | Configure your Wi-Fi Direct network settings manually. | |
Group Owner | - | - | Set your machine as the Group Owner. | |
Device Info. | Device Name | - | View your machine's device name. | |
SSID | - | View the Group Owner's SSID. When the machine is not connected, the LCD displays Not Connected. | ||
IP Address | - | View your machine's current IP Address. | ||
Status Info. | Status | - | View the current Wi-Fi Direct network status. | |
Signal | - | View the current Wi-Fi Direct network signal strength. When your machine acts as Group Owner, the LCD always indicates a strong signal. | ||
Channel | - | View the current Wi-Fi Direct network channel. | ||
Speed | - | View the current Wi-Fi Direct network speed. | ||
I/F Enable | - | - | Turn the Wi-Fi Direct connection on or off. | |
Network Reset | - | - | - | Restore all network settings back to the factory settings. |
[Print Reports]
Level 1 | Level 2 | Descriptions |
|---|---|---|
User Settings | - | Print a list of your settings. |
Print Settings | - | Print a list of your Printer settings. |
Network Config (For models with network function) | - | Print a list of your Network settings. |
PrintFileList (Available only for certain models) | - | Print a list of data saved in the machine's memory. |
Drum Dot Print | - | Print the Drum Dot Check Sheet. |
WLAN Report (For models with wireless network function) | - | Print the wireless LAN connection results. |
[Machine Info.]
Level 1 | Level 2 | Descriptions |
|---|---|---|
Serial No. | - | Check your machine's serial number. |
Version | - | Check your machine's firmware version. |
Page Counter | Total | Check the total number of pages the machine has printed during its life. |
Copy | ||
Other | ||
Parts Life | Toner | View the approximate remaining toner life. |
Drum | You can check the percentage of Drum life that remains available. | |
[Initial Setup]
Level 1 | Level 2 | Descriptions |
|---|---|---|
Reset | Machine Reset | Restore all the machine settings that you have changed. |
Network Reset (For models with network functionality) | Restore all network settings back to the factory settings. | |
All Settings | Restore all the machine's settings back to the factory settings. | |
Factory Reset | Restores all the machine's settings to the factory defaults. Perform this operation when you dispose of your machine. | |
Local Language (Available only for certain models) | - | Change your LCD language. |