FAQs & Troubleshooting

Close

GS3710

FAQs & Troubleshooting

FAQs & Troubleshooting

Date: 27/07/2012 ID: faqh00000438_005

How do I wind the bobbin?

Winding the bobbin


  • Only use the bobbin that comes with this machine or bobbins of the same type (part code: SA156, SFB: XA5539-151). Using other bobbins may cause damage to the machine.
  • We designed the bobbin that comes with this machine. If you use bobbins from other models, the machine will not work properly.

    The bobbin for this model and the bobbin for other models.


    (1) This model
    (2) Other models
    (3) 11.5 mm (7/16 inch)


  1. Pull up the spool pin completely.

    Pull up the spool pin completely.


  2. Put a spool of thread on this pin.

    Put a spool of thread on spool pin.


    If the spool of thread is in the wrong place, or is set incorrectly, the thread may tangle on the spool pin.


  3. While holding the thread from the spool with your right hand, pass the thread toward you, in the groove on the thread guide. Then, pass the thread around the pre-tension disk and pull the thread in completely.

    Pass the thread in the groove on the thread guide, and then, pass the thread around the pre-tension disk and pull the thread in completely.


    (A) Pre-tension disk


    Make sure that the thread passes under the pre-tension disk.



  4. Pass the end of the thread through the hole on the bobbin from the inside of the bobbin.

    Pass the end of the thread through the hole on the bobbin from the inside of the bobbin.


  5. Put the bobbin onto the bobbin winder shaft and slide the bobbin winder shaft to the right. Turn the bobbin clockwise, by hand, until the spring on the shaft slides into the notch of the bobbin.

    Put the bobbin onto the bobbin winder shaft and slide the bobbin winder shaft to the right.


    (1) Spring on the shaft
    (2) Notch
    * Align the notch of the bobbin to the spring on the shaft.
    (3) 7 - 10 cm (2-3/4 to 3-15/16 inches)


    Make sure to pull out 7 to 10 cm (2-3/4 to 3-15/16 inches) of thread from the hole on the bobbin.


    Pull the thread taut and hold the end of the thread straight up. If the thread is too short, not pulled taut or held at an angle, injuries may occur when the thread is wound around the bobbin.


  6. Turn on the machine.

    Turn on the machine.


  7. While holding the end of the thread, gently press the foot controller to wind the thread around the bobbin a few times. Then stop the machine.

    While holding the end of the thread, gently press the foot controller to wind the thread around the bobbin a few times, and then stop the machine.


    (1) 7 - 10 cm (2-3/4 to 3-15/16 inches)


  8. Trim the excess thread above the bobbin.

    Trim the excess thread above the bobbin.


    (1) Leave 1 cm (1/2 inch) of thread from the hole on the bobbin.


    Make sure you follow the instructions carefully. If you do not cut the excess thread completely before winding the bobbin, when the thread runs low it may tangle around the bobbin and cause the needle to break.


  9. Press the foot controller to start.

    Press the foot controller to start.


  10. When the bobbin seems full and begins spinning slowly, take your foot off the foot controller.

    When the bobbin seems full and begins spinning slowly, take your foot off the foot controller.


  11. Cut the thread, slide the bobbin winder shaft to the left and remove the bobbin.

    Cut the thread, slide the bobbin winder shaft to the left and remove the bobbin.


    • When the sewing machine is started or the handwheel is turned after winding the thread around the bobbin, the machine will make a clicking sound; this is not a malfunction.
    • The needle bar does not move when you slide the bobbin winder shaft to the right.

Not winding the bobbin properly may cause the thread tension to loosen, and may break the needle.


Wound evenly and wound poorly


(1) Wound evenly
(2) Wound poorly

Related Models

GS2500, GS2510, GS2520, GS2700, GS3700, GS3710, GS3750WT, LX27NT, SL300, TY400G

If you need further assistance, please contact Brother customer service:

Content Feedback

To help us improve our support, please provide your feedback below.
Step 1: How does the information on this page help you?
Step 2: Are there any comments you would like to add?

Please note this form is used for feedback only.