In order to use the Scan to E-mail Server option, the Brother machine will need to be connected to a network and have access to a POP3 and SMTP server. If you do not have this information, please contact your Internet Service Provider or Network Admin to obtain the information.


I: Set up Scan to E-mail (E-Mail Server)

1. Print the network configuration report to obtain the IP address of the Brother machine. (Click here to see how to print the Network Configuration List.)
    
2. Open a web browser (such as Internet Explorer) and enter in the IP address of the Brother machine as http://[Brother machine's IP Address].
    

   [Brother machine's IP Address] is listed on the Network Configuration Sheet.

    

    

3. Click the Network tab.
    
4. Click Protocol.
    
5. Place a check next to POP3/SMTP if it is not already checked, then click Advanced Setting.
    
6. Within this section, you will be able to configure your Incoming and Outgoing mail server settings. Fill in all the requested information on this page. If you are unsure about any of these settings, contact your Internet Service Provider or Network Admin for support:
   
   

    

   1. SMTP Server Address: This field displays the Host Name or IP address of an SMTP mail server (outgoing E-mail Server) on your network. (Ex: smtp.example.net or 192.0.0.1) If you are using the DNS name of the SMTP E-mail server, you must use the FQDN (Full Qualified Domain Name) such as smtp.example.net
       
   2. SMTP Port: Specify the destination port number of the SMTP server that you will connect to.
       
   3. SMTP Server Authentication Method: Specify the authentication method for the SMTP server. This value determines which type of method is used to authenticate the user to the SMTP server. The options are as follows:

       

      • None: Does not authenticate to the SMTP Server.
         
      • SMTP-AUTH: Uses the method which is SMTP Authentication. If this method is used, it is necessary to set the SMTP account details correctly.
         
      • POP before SMTP: Uses the method "POP before SMTP". If this method is used, it is necessary to set POP3 account settings correctly.

       

   4. SMTP-AUTH Account Name/Password: Specify a name and password to be validated with the SMTP server and retype the password for comparison. To set for no password, enter a single space.
       
   5. SMTP over SSL/TLS: You can choose the encryption method between the machine and the SMTP server. You may check or uncheck Verify Server Certificate, which verifies the certificate between the machine and the SMTP server.
       
   6. Printer E-mail Address: Enter the e-mail address of the printer. If an administrator address has not been correctly entered, the Notification Mail will be sent to the printer. If you do not set a printer e-mail address, the Notification Mail is not sent to the administrator.
       
   7. POP3 Server Address: This field determines the host name or IP address of the POP3 server (incoming e-mail server). (Ex: pop.example.net -or- 192.0.0.1)
       
      If you are using the DNS name of the POP3 E-mail server you must use the FQDN (Fully Qualified Domain Name) such as pop.example.net.
       
   8. POP3 Port: Specify the destination port number of the POP3 server that you will connect to.
       
   9. Mailbox Name/Password: Specify a mailbox name and password on the POP3 server where the Internet print jobs are to be retrieved. To set for no password, enter a single space
       
   10. Use APOP: Check this box to specify whether APOP is used or not when logging in to the POP3 server.
        
   11. POP3 over SSL/TLS: You can choose the encryption method between the machine and the POP3 server. You may check or uncheck Verify Server Certificate, which verifies the certificate between the machine and the POP3 server.
        
   12. Segmented Message Timeout: If a print job is separated into multiple email messages using the segmented message feature of the print server, this value indicates how long the print server will wait for all of the segments of the message to arrive.

    

7. Click Submit. You will briefly see a message stating: Data updated successfully.
    
8. A screen will appear labeled: Test E-Mail Send/Receive Configuration. Choose from the following options then click Submit:
   
   

    

   • Test E-mail Send Configuration
      
   • Destination E-mail Address: Enter the destination e-mail address.
      
   • Send Test E-mail
      
   • Test E-mail Receive Configuration

    

9. You will see a message stating: Testing Email Configuration followed by the test results. Once you have are finished viewing the results, click OK.

II: To setup and Scan to E-mail Server using One Touch or Speed Dial locations

1. While still within the Web Home Page, click on the Address tab.
    
2. Choose a set of One Touch or Speed Dial locations that you want to use.
    
3. For each storage location that you wish to program, enter the following information:

    

   • Number/E-mail Address: The recipient's email address.
      
   • Name: The recipient's name.
      
   • Type: Select Mail [color type] (where [color type] is the Color, Gray or B&W followed by file format you want).
      
   • Quality: Select the resolution you want.
      
   • PDF Type: When you choose the PDF, select the file type you want.
      
4. Click Submit.
    
5. After the One Touch or Speed Dial locations are configured and you want to Setup Group locations, click Setup Groups G1-G20. Configure the following settings for each group:

    

   • Group #: Choose a vacant One Touch or Speed Dial location to store you group (One Touch dial locations are with " * " . Speed Dial locations are with " # " ).
      
   • Name: The group's name.
      
   • Type: Select Mail [color type] (where [color type] is the Color, Gray or B&W followed by file format you want).
      
   • Quality: Select the resolution you want.
      
   • PDF Type: When you choose the PDF, select the file type you want.
      
   • Members: Click Select and choose the members to include in this group by placing a check next to each desired One Touch or Speed Dial location.

    

6. Click Submit.
   
   

III: Scan to E-mail Server without using One-Touch or Speed Dial numbers:

1. Load your document.
    
2. Press  (Scan).
    
3. Press the Up or Down arrow key to choose Scan to E-mail.
   Press OK.

    

   • If your machine does not support Duplex Scan, go to step 5.
      
   • If your machine supports Duplex Scan, go to step 4.

    

4. Press the Up or Down arrow key to choose 1sided, 2sided (L)edge or 2sided (S)edge.
   Press OK.
    
5. Do one of the following:

    

   • If you don’t have to change the quality, press the Up or Down arrow key to choose Enter Address.
     Press OK and then go to step 8.
      
   • If you want to change scan settings, press the Up or Down arrow key to choose Change setting.
     Press OK.

    

6. Press the Up or Down arrow key to choose the type and resolution for scanning you want, press OK.
    
7. Press the Up or Down arrow key to choose the file type you want, press OK.
   
    
8. Enter the E-mail address (Up to 60 characters).
    
9. Press Start.
   The machine starts the scanning process.