MFC-L2759DW
FAQs & Troubleshooting |
MFC-L2759DW
Date: 01/31/2022 ID: faq00002256_508
Clean the Drum Unit Using Drum Dot Print
If your printout has dots or other repeating marks at 3.7 in. (94 mm) intervals, the drum may have foreign material, such as glue from a label, stuck on the drum surface.
HL-L2390DW/DCP-L2550DW/MFC-L2690DW/MFC-L2690DWXL/MFC-L2710DW/MFC-L2717DW
- Make sure the machine is in Ready mode.
- Press or to display the [Print Reports] option, and then press OK.
- Press or to select the [Drum Dot Print] option.
- Press Start.The machine prints the Drum Dot Check Sheet.
- Press and hold to turn off the machine.
- Open the front cover.
- Remove the toner cartridge and drum unit assembly from the machine.
- Push down the green lock lever and take the toner cartridge out of the drum unit.
- Turn the drum unit as shown in the illustration. Make sure that the drum unit gear is on the left side.
- Use the numbered markers next to the drum roller to find the mark on the drum. For example, a dot in column 2 on the check sheet means that there is a mark in drum region “2”.
- Turn the edge of the drum unit toward you while looking at the drum surface to find the mark.
- IMPORTANT
-
- To avoid print quality problems, DO NOT touch the surface of the drum unit, only the wheel on the end.
- Wipe the surface of the drum gently with a dry cotton swab until the mark or foreign material on the surface comes off.
- NOTE
- DO NOT clean the surface of the photosensitive drum with a sharp object or any liquids.
- Push the toner cartridge firmly into the drum unit until you hear it lock into place.Make sure you put the toner cartridge in correctly or it may separate from the drum unit.
- Install the toner cartridge and drum unit assembly back into the machine.
- Close the front cover of the machine.
- Press to turn on the machine.
HL-L2395DW/MFC-L2730DW/MFC-L2750DW/MFC-L2750DWXL
- Make sure the machine is in Ready mode.
- Press .
- Press [Yes].The machine prints the Drum Dot Check Sheet.
- Press .
- Press and hold to turn off the machine.
- Open the front cover.
- Remove the toner cartridge and drum unit assembly from the machine.
- Push down the green lock lever and take the toner cartridge out of the drum unit.
- Turn the drum unit as shown in the illustration. Make sure that the drum unit gear is on the left side.
- Use the numbered markers next to the drum roller to find the mark on the drum. For example, a dot in column 2 on the check sheet means that there is a mark in drum region “2”.
- Turn the edge of the drum unit toward you while looking at the drum surface to find the mark.
- IMPORTANT
-
- To avoid print quality problems, DO NOT touch the surface of the drum unit, only the wheel on the end.
- Wipe the surface of the drum gently with a dry cotton swab until the mark or foreign material on the surface comes off.
- NOTE
- DO NOT clean the surface of the photosensitive drum with a sharp object or any liquids.
- Push the toner cartridge firmly into the drum unit until you hear it lock into place.Make sure you put the toner cartridge in correctly or it may separate from the drum unit.
- Install the toner cartridge and drum unit assembly back into the machine.
- Close the front cover of the machine.
- Press to turn on the machine.
DCP-L2550DW, HL-L2390DW, HL-L2395DW, MFC-L2690DW, MFC-L2710DW, MFC-L2717DW, MFC-L2730DW, MFC-L2750DW(XL), MFC-L2759DW
If you need further assistance, please contact Brother customer service:
Content Feedback
To help us improve our support, please provide your feedback below.
Step 1: How does the information on this page help you?
Step 2: Are there any comments you would like to add?
Please note this form is used for feedback only.