FAQs & Troubleshooting

Close

SDX1200

FAQs & Troubleshooting

FAQs & Troubleshooting

Date: 11/03/2019 ID: faqh00101341_000

Retrieving Roll Feeder Data On the Machine and Cutting

 

Retrieve data created in CanvasWorkspace on the cutting machine, and then cut the material with the roll feeder.

 

 

Retrieving the Data

 

  1. After selecting Roll Feeder in the home screen, select Start to cut rolled material in the screen shown below.
    image image image
     



     
  2. Select the location of the data to be retrieved, and then select the desired pattern.
    image

    (1) Retrieve from a USB flash drive.

     

    (2) Retrieve from CanvasWorkspace
    (via a wireless network connection).

     

    (3) Retrieve from CanvasWorkspace
    (using a USB cable).



    (1) Retrieve from a USB flash drive.
    image image

    image

    Select the desired data.  

    Confirm the data, and then touch the OK.



    (2) Retrieve from CanvasWorkspace (via a wireless network connection).
    (3) Retrieve from CanvasWorkspace (using a USB cable).


    image
     

    A preview screen for the pattern layout appears when transferring the data from the CanvasWorkspace is completed.

 

▲TOP

 

 

 

 

Cutting the Material

 

  1. Make sure that the auto blade holder has been installed in the carriage of the machine.





     
  2. Raise the scanner lever (on the left side of the machine) to “2”.

    image




     
  3. Select Cut in the preview screen.
    image image image
     





     
  4. To perform trial cutting, touch the Test.
    image

    When the roll feeder is used, half-cutting is automatically. Touch image to check the settings.







     
  5. To perform trial feeding, touch  image . 
    Before cutting, you can check if the material can be fed in straight and whether the length of the material is sufficient for the length of the cutting pattern.

    image





     
  6. To change the cutting start position, touch image . 
    The cutting start position can be moved up or down (in the feeding direction) to the desired location.

    image





     
  7. Touch the Start to start cutting. When cutting is finished, the machine stops at the bottom of the pattern.

    image





     
  8. To cut off the material at the point where cutting stopped, select Finish.

    image


    When finish cutting,

    >>go to step 9.



    When selecting Continue to cut, you can continue cutting additional patterns without cutting off the material.
     

    If you cut repeatedly the same pattern,
     >repeat the operation from step 3.

    If you cut a different pattern,
     >go to Continuing to cut with a different pattern.






     
  9. The following screen to move the rolled material appears. Click OK.

    image





     
  10. Remove the trimmer from the roll holder. 
    Install the trimmer over the material.
    image image image
    (1) Trimmer   (2) Hole in trimmer
    (3) Pin on base attachment
     * Combine (2) with (3)
     





     
  11. Firmly press the trimmer down on the right side of the material.
    While holding them in place, slide the trimmer blade from right to left to cut off the material.
    Slide the trimmer blade while pressing down gently.
    image (1) Trimmer
    (2) Trimmer blade





     
  12. After cutting off the material, confirm the instructions and then touch the OK.

    image





     
  13. To feed out the cut-off material, touch the OK.

    image

 

▲TOP

 

 

 

 

Continuing to cut with a different pattern

 

  1. Touch Continue to cut.

    image





     
  2. Touch image in the preview screen.

    image
    >> When image is touched, the message OK to delete data showing on the screen? appears. Touch the “OK” key.






     
  3. Select Start to cut rolled material, and then retrieve a different pattern.

    image

    If you send the data via a wireless connection or a USB cable, you must send a new data for the roll feeder with the CanvasWorkspace.
    Refer to Instructions for Creating Roll Feeder Data with CanvasWorkspace and Sending It to the Cutting Machine.
    After sending the data, try cutting from step 2.

    If you retrieve the data using a USB flash, go back to step 2 and try again.

 

▲TOP

 

 

Related Models

SDX1200

If you need further assistance, please contact Brother customer service:

Content Feedback

To help us improve our support, please provide your feedback below.
Step 1: How does the information on this page help you?
Step 2: €Are there any comments you would like to add?

Please note this form is used for feedback only.