Preguntas frecuentes y solución de problemas

Cerrar

GL-100

Preguntas frecuentes y solución de problemas

Preguntas frecuentes y solución de problemas

Fecha: 29/11/2018 ID: faqp00001504_000

The ink ribbon (black tape) got caught in between the tape layers and came out of the printer, and the tape cannot be used.

This can happen when you install the tape cassette with the ink ribbon (black tape) loose, or pull out the printed tape by hand.
ink ribbon

 

If the ink ribbon is not separated from the tape cassette, you can fix this by winding the spool to reel the ink ribbon as shown below.

  • Be sure to wind the spool in the correct direction.
  • If the ink ribbon is broken, you cannot reel it. Replace the tape cassette with a new one.
    Spool
    1. Spool

    Using a tape cassette with broken ink ribbon may cause the printer to break. Use a new tape cassette.

 

Please remember the following precautions for future use.

 

  • Is the end of the tape fed correctly through the tape guide?
    If not, feed the end of the tape under the tape guide as shown below.
    Tape guide
    1. End of tape
    2. Tape guide

     

  • Does the underside of the tape cassette completely touch the base of the compartment?
    If the tape cassette is not installed correctly, the laminated tape may become misaligned, or the tape may get jammed in the printer. When installing the tape cassette, make sure that the entire underside of the tape cassette, especially near the tape exit, is touching the base of the compartment.
    Installing tape cassette
    1. End of tape
    2. Tape exit slot
  • Do not pull the tape out of the tape exit slot.
    Pulling out the tape by hand could cause the ink ribbon to come out with the tape.

    If you pulled out excessive length of tape, cut the tape with scissors only when the ink ribbon has not come out. Check that the end of the tape feeds under the tape guide, and then reinstall the tape cassette.

    Tape guide
    1. End of tape
    2. Tape guide
  • Do not install the tape cassette with the ink ribbon loose.
    If the ink ribbon is loose, use your finger to wind the spool in the direction of the arrow in the illustration below. Be sure to wind the spool in the correct direction.
    Spool
    1. Spool
  • Do not cover the tape exit slot while printing.
       
  • Do not cut the tape until printing and feeding are complete.

Preguntas frecuentes relacionadas

Modelos relacionados

GL-100, PT-1000, PT-1090, PT-1180, PT-1230PC, PT-1280, PT-1400, PT-1500PC, PT-1600, PT-1650, PT-1700, PT-1750, PT-1800, PT-1810, PT-1830, PT-18R, PT-1900, PT-1910, PT-1950, PT-1960, PT-2030, PT-2030AD, PT-2300, PT-2310, PT-2400, PT-2410, PT-2430PC, PT-2470, PT-2500PC, PT-2700, PT-2710, PT-2730, PT-7500, PT-7600, PT-9200DX, PT-9200PC, PT-9500PC, PT-9600, PT-9700PC, PT-9800PCN, PT-D400, PT-D410, PT-D450, PT-D600, PT-D610BT, PT-E300, PT-E500, PT-E550W, PT-H300, PT-H500, PT-P700, PT-P750W, PT-P900W, PT-P950NW

Si necesita asistencia, contáctese con el servicio al cliente de Brother:

Comentarios sobre el contenido

Para ayudarnos a mejorar el soporte, bríndenos sus comentarios a continuación.
Paso 1: ¿Cómo lo ayudó la información en esta página?
Paso 2: ¿Quiere agregar otros comentarios?

Observe que este formulario solo se utiliza para comentarios.