PJ-622
![]() |
FAQs & Troubleshooting |
![](/g/b/img/product/pj622euk.jpg)
PJ-622
Date: 17/09/2019 ID: faqp00001466_001
What do the indicator lights mean?
The indicators light and flash to indicate the printer's status. The following symbols are used in this FAQ to explain the meaning of the different indicator colours and patterns.
![]() ![]() ![]() |
Indicator is lit in the colour shown |
![]() ![]() ![]() |
Indicator is blinking in the colour shown |
![]() ![]() |
Indicator is blinking in alternating colours as shown |
![]() |
Indicator is lit or blinking in any colour or pattern |
![]() |
Indicator is off |
POWER | DATA | STATUS | Bluetooth® *1 | Description | Solution |
---|---|---|---|---|---|
![]() |
![]() |
![]() |
![]() |
AC adapter / DC cable / Rechargeable Li-ion battery in use | |
![]() |
![]() |
![]() |
![]() |
Rechargeable Ni-MH battery in use | |
![]() |
![]() |
![]() |
![]() |
Rechargeable battery in use, battery charge is full | |
![]() |
![]() |
![]() (Once every 4 seconds) |
![]() |
Rechargeable battery in use, battery charge is half-full | |
![]() |
![]() |
![]() (Twice every 4 seconds) |
![]() |
Rechargeable battery in use, battery charge is low | |
![]() |
![]() |
![]() (Once every second) |
![]() |
Rechargeable battery needs to be charged | |
![]() |
![]() |
![]() |
![]() |
Rechargeable Ni-MH battery is discharging | |
![]() |
![]() |
![]() |
![]() |
Rechargeable Ni-MH battery is charging | |
![]() |
![]() |
![]() |
![]() |
Printing or receiving data | |
![]() |
![]() |
![]() |
![]() |
Buffer contains unprinted data | |
![]() |
![]() |
![]() |
![]() |
Receiving flash upgrade | |
![]() |
![]() |
![]() |
![]() |
Printer Receiving upgrade | |
![]() |
![]() |
![]() |
![]() |
Printer is in service mode (for cleaning the platen roller or printing a printer report) | |
![]() |
![]() |
![]() |
![]() |
System error (call for service) | |
![]() |
![]() |
![]() |
![]() |
The POWER indicator does not light |
The printer is receiving no power. If you are using AC or DC power, make sure that the AC adapter or DC cable is properly connected (See "How to connect to an AC power outlet (Optional)" or "How to connect to a DC power outlet (Optional)".) and make sure that the AC or DC power outlet is turned on. If you are using DC power, check the fuse. |
![]() |
![]() |
![]() |
![]() |
No rechargeable Ni-MH battery found when charging |
The printer did not detect a rechargeable Ni-MH battery when you tried to charge the battery.
If the rechargeable Ni-MH battery is connected properly, the battery may have overheated while charging. Allow the rechargeable Ni-MH battery to cool before charging it again. If this is a reoccurring problem, replace the rechargeable Ni-MH battery. |
![]() |
![]() |
![]() |
![]() |
Time-out when charging the rechargeable Ni-MH battery | Too much time is needed to charge the rechargeable Ni-MH battery (normally the battery should be fully-charged within 120 minutes). Replace the rechargeable Ni-MH battery. |
![]() |
![]() |
![]() |
![]() |
Head or motor is cooling down |
The thermal head or motor is too hot. This condition may occur more often when the printer is used at high altitude (more than 10,000 feet) due to a lower air density available to cool the printer. |
![]() |
![]() |
![]() |
![]() |
Data reception error |
Data is not being received properly, most likely because of a poor IrDA connection. Reposition the printer and/or IrDA port on the computer and try again. |
![]() |
![]() |
![]() |
![]() |
Buffer full or format error | |
![]() |
![]() |
![]() |
![]() |
Printer is in boot mode |
The AC adapter was unplugged while the firmware was being updated, and the printer started up in boot mode the next time it was started. Contact your reseller or Brother Customer Service for assistance. |
![]() |
![]() |
![]() |
![]() |
Ready for Bluetooth communication |
PJ-622, PJ-623, PJ-662, PJ-663
If you need further assistance, please contact Brother customer service:
Content Feedback
Please note this form is used for feedback only.