CM300
![]() |
Preguntas frecuentes y solución de problemas |
![](/g/b/img/product/hf_cm300euk.jpg)
CM300
Fecha: 03/04/2023 ID: faqh00100655_000
Cut a thin fabric for the quilt piece. (How to use the High Tack Adhesive Fabric Support Sheet.)
Use the high tack adhesive fabric support sheet to attach fabrics for quilt piecing to the standard mat. These sheets should only be used with patterns that have a seam allowance. Use the Iron-on fabric appliqué contact sheet to cut a pattern that has no seam allowance. The high tack adhesive fabric support sheet can be repeatedly used until their adhesive strength has decreased. (Once the support sheet has been peeled off the mat, it can no longer be used.)
-
Peel off the protective sheet from the adhesive side of the standard mat.
- Do not discard the protective sheet peeled off the mat; save it for later use.
- In order to maintain the adhesive strength, attach the protective sheet to the adhesive side of the mat after use. When the mat is not being used, clean the adhesive side and affix the protective sheet before storing it. For details, see “Cleaning the Mat”.
-
With the glossy side of the high tack adhesive fabric support sheet facing down, attach it to the mat’s adhesive side.Slowly attach the support sheet from its edges so that no air is trapped between the mat and the sheet.
(1) Glossy side of support sheetPlace the support sheet within the attaching area (grid area) on the adhesive side of the mat.If the sheet extends from the attaching area, it may be damaged by the feed rollers when the mat is fed.
-
Peel off the backing from the top of the support sheet.
(1) Backing
(2) Adhesive -
Test attaching the material.
Before attaching the material to the mat, use a corner of the adhesive side of the mat to test attaching it.
-
From its edges, attach the material to the adhesive side of the mat so that there are no wrinkles in the material.
- Be sure to first iron the fabric to remove any wrinkles.
- Place the material within the attaching area (grid area) on the adhesive side. If the material extends from the attaching area, it may be damaged by the feed rollers when the mat is fed.
- The mat does not have a top and bottom. It can be inserted into the feed slot from either end.
- Be sure that the vertical grain of the attached fabric runs straight up and down. The built-in patterns are automatically arranged suitable for fabric with vertical grain.
- When drawing a seam allowance, attach the fabric to the mat with its wrong side facing up.
-
Firmly move the spatula handle across the surface of the fabric to remove any wrinkles and firmly attach the fabric to the mat.
(1) Spatula
Peeling Off the Material
Be sure adjusting the blade extension, installing the holder and trial cutting to prepare for cutting.
After cutting the material, use a spatula to slowly peel off just the fabric.
Try not to peel off the support sheet.
|
(1) Fabric cut out (2) Support sheet remaining on mat |
-
The support sheet may be unintentionally peeled off while you are removing the fabric from the mat under the following conditions:
- The adhesive between The mat and support sheet is becoming weak after repeated uses.
- The support sheet tends to be strongly attached to a certain types of fabrics.
In this case, use the included spatula to hold the support sheet on the mat and remove the fabric using your hand. - After cutting, carefully remove any fibers remaining on the support sheet.
- When attaching fabric with an iron-on sheet attached or paper to the mat, cleanly peel off the support sheet from the mat, or attach the material to a different standard mat without a support sheet attached.
- Do not leave material attached to a mat with a support sheet attached for a long period of time; otherwise, the adhesive will permeate the material.
Notice on Use of High Tack Adhesive Fabric Support Sheet
- When the sheet’s adhesive strength decreasesor fabric becomes twisted while being cut, replace the sheet with a new one.
- When peeling the sheet off the mat or replacing the sheet, use the spatula to carefully remove the old sheet.
- Store the mat in between uses with the protective sheet affixed to the support sheet.
- If a mat with a support sheet attached is not to be used for a certain length of time, peel the support sheet off the mat and affix the protective sheet on the adhesive side of the mat before storing it.
- Do not reuse a support sheet that has been attached to the mat.
- Store the support sheet at room temperature and in a location not exposed to high temperatures, high humidity or direct sunlight.
- Do not bend the support sheet to store it.
En el caso de que necesite ayuda adicional, póngase en contacto con el servicio de atención al cliente de Brother:
Comentarios sobre el contenido
Tenga en cuenta que este formulario solo se utiliza para comentarios.