FAQs & Troubleshooting

Close

Innov-is NS2750D

FAQs & Troubleshooting

FAQs & Troubleshooting

Innov-is NS2750D

Not your product?

Date: 07/31/2023 ID: faqh00000637_004

How do I attach or remove the Embroidery Unit?

Attaching the Embroidery unit

  • Do not move the machine with the embroidery unit in place. The embroidery unit may be dropped and cause injury.
  • Keep your hands and other objects away from the embroidery carriage and frame. Otherwise injury may result.
  • Do not touch the connector in the embroidery unit connector slot. The connector could be damaged, and it may cause malfunctions.
  • Do not lift up on the embroidery carriage, and do not forcefully move it. It may cause malfunctions.



 

 

  1. Turn the main power to OFF.

    Before attaching the embroidery unit, be sure to turn off the machine. Otherwise, injuries may occur if one of the operation buttons is accidentally pressed and the machine starts sewing.


  2. Pull the flat bed attachment off to the left.


     

  3. Slide the tab on the cover of the connection port in the direction of the arrow to open the cover.

    image

    Be sure to close the cover of the connection port when the embroidery unit is not being used.

     

  4. Insert the embroidery unit connector into the connection port, and then lightly push in the embroidery unit until it snaps into place.
    (1) Connection port

    (2) Embroidery unit connector

    • Make sure that there is no gap between the embroidery unit and the machine, otherwise the embroidery pattern may not be sewn correctly. Be sure to fully insert the connector into the connection port.
    • Do not push on the carriage when attaching the embroidery unit to the machine, otherwise damage to the embroidery unit may result.

     

  5. Turn on the machine.

    A message appears in the screen.

     

  6. Be sure that no objects or hands are near the embroidery unit and press "OK".

    image

    The carriage moves to its initial position.
    (1) Carriage

    Keep your hands and foreign objects away from the embroidery carriage and frame when the machine is embroidering. Otherwise, injury may result.

    • If the machine was not initialized correctly, the initial screen may not appear. This is not a sign of a malfunction. If this occurs, turn the machine off, then on again.
    • A confirmation message to lower the frame-securing lever after the carriage moves to its initial position is displayed. Continue with pattern selection and remember to lower the frame-securing lever when the embroidery frame is attached.

    The screen for selecting the embroidery pattern type is displayed.

    image

    Utility stitches cannot be selected when the embroidery unit is attached.

 

Removing the Embroidery Unit

Make sure that the machine is completely stopped and follow the instructions below.

 

  1. Remove the embroidery frame.

    For details on removing the embroidery frame, refer to How do I attach or remove the embroidery frame?
     

  2. Press image , and then press "OK" .

     

    image
    The embroidery carriage moves into a position where it can be stored.

     

  3. Turn off the machine.

    Always turn off the machine before removing the embroidery unit. It may cause malfunctions if removed when the machine is turned on.

     

  4. Hold the release button on the bottom left of the embroidery unit, and slowly pull the embroidery unit to the left.
    (1) Release button

    Do not carry the embroidery unit by holding the release button compartment.

 

 

Related FAQs

Related Models

Innov-is NS2750D, Innov-is NS2850D, SE2000

If you need further assistance, please contact Brother customer service:

Content Feedback

To help us improve our support, please provide your feedback below.
Step 1: How does the information on this page help you?
Step 2: Are there any comments you would like to add?

Please note this form is used for feedback only.