QB9110L
![]() |
FAQs & Troubleshooting |
Tangled thread on wrong side of fabric
Symptom / Cause
-
The thread becomes tangled on the lower side of the fabric.
- After starting sewing, a rattling noise is made and sewing cannot continue.
-
Looking under the fabric, there is tangled thread in the bobbin case.
If the upper thread is incorrectly threaded, the upper thread passed through the fabric cannot be firmly pulled up and the upper thread becomes tangled in the bobbin case, causing a rattling noise.
Remedy / Check details
Remove the tangled thread, and correct the upper threading according to the following procedure.
-
Turn off the sewing machine.
-
Remove the tangled thread. If it cannot be removed, cut the thread with scissors.
-
If the threads remain in the bobbin case, remove the needle plate cover, and then remove the threads.
For details, refer to How do I clean the machine? (Cleaning the race)
If the bobbin was removed from the bobbin case, install the bobbin in the bobbin case correctly.
Refer to How do I install the bobbin wound with thread? -
Remove the upper thread from the machine.
-
Turn on the sewing machine.
-
Raise the presser foot using the presser foot lever.
(1) Presser foot lever
If the presser foot is not raised, the sewing machine cannot be threaded correctly.
-
Press
(needle position button) once or twice to raise the needle.
-
Pull some thread off the spool, and then pass the thread under the thread guide.
(1) Thread guide
-
Pass the thread under the thread guide cover from the back to the front.
Hold the thread with your right hand so that there is no slack in the thread that is pulled out, and then pass the thread under the thread guide cover with your left hand.
(1) Thread guide cover
-
Feed the upper thread as shown in the illustration below.
-
Make sure you guide the thread through the thread take-up lever from right to left as shown in the illustration below.
Sewing is possible only if the thread is securely hooked on the thread take-up lever.
(1) Thread take-up lever
-
Put the thread behind the needle bar thread guide above the needle.
The thread can easily be passed behind the needle bar thread guide by holding the thread in your left hand, then feeding the thread with your right hand.(1) Needle bar thread guide -
Turn off the sewing machine.
-
Lower the presser foot lever.
(1) Presser foot lever -
While lowering the needle threader lever, hook the thread onto the guide.
(1) Needle holder (2) Needle threader lever
(3) Guide
-
Fully lower the needle threader lever.
If the needle is not raised to it's highest position, the needle threader cannot thread the needle.Turn handwheel counterclockwise until the needle is at its highest position.
(1) Mark on handwheel -
Catch the thread on the hook as shown below.
(1) Hook
(2) Thread -
While lightly holding the thread, release the needle threader lever. The hook will pull the thread through the needle.
-
Pull the loop of the thread passed through the eye of the needle toward the rear of the machine.
(1) Loop of thread
Be careful not to pull on the thread with force or it may bend the needle.
-
Raise the presser foot lever.
(1) Presser foot lever -
Pass the end of the thread through the presser foot, and then pull out about 5 cm (2 inches) of thread toward the rear of the machine.
(1) 5 cm (2 inches)
Related Models
CE8100, CP2410, CP-6500, CP-7500, CS7130, CS7205, DZ2400, DZ2750, DZ3000, DZ3400, HC1850, HC3010, HC7140, HS-2500, PS300T, QB9110L, SB1000T, SC3000, SC9500, SM8270, SQ9100, SQ9130, SQ9185, SQ9285, SQ9310, XR1300, XR1355, XR3140, XR3240, XR3340, XR9550/XR9550PRW, XS2070, XS2080, XS2100, XS3109