CM550DX/ CM550
 |
FAQs & Troubleshooting |
Important Information about Mat
The cutting mats compatible with this machine have been redeveloped with a different design, type, function, etc.
Therefore, use the redeveloped mats in addition to the mats described in the Operation Manual.
Before using the redeveloped mats, be sure to refer to the following table since the mat functions have changed.
In addition, the timing of mat redevelopment differs depending on the sales region.
Redeveloped mats that can be used with various materials
Redeveloped mats that can be used with various accessories
Details on each mat
| Mat before being redeveloping |
Redeveloped Mat |
||||
|---|---|---|---|---|---|
| Part Code | Part Name | Part Code | Part Name | ||
| CAMATF12 | Standard mat 12" x 12" |  |
CAMATSTD12 | Standard mat 12" x 12" |  |
| CAMATF24 | Standard mat 12" x 24" | CAMATSTD24 | Standard mat 12" x 24" | ||
| CAMATM12 | Middle tack adhesive mat 12" x 12" |
 |
―* |
||
| CAMATM24 |
Middle tack adhesive mat 12" x 24" |
||||
| CAMATP12 |
Low tack adhesive mat 12" x 12" |
 |
CAMATLOW12 | Low tack adhesive mat 12" x 12" |
 |
| CAMATP24 |
Low tack adhesive mat 12" x 24" |
CAMATLOW24 | Low tack adhesive mat 12" x 24" |
||
* The middle tack adhesive mat has been discontinued.
Use the standard mat or low tack adhesive mat with materials and accessories that had been used with the middle tack adhesive mat.
The mat to be used differs depending on the material or accessory. For details, refer to the following table.
You can continue to use the middle tack adhesive mat with your cutting machine.
Redeveloped mats that can be used with various materials
- The appropriate use for each type of mat is indicated in the following table.
- Before attaching the material to the mat, use an edge of the adhesive side of the mat to test attaching the material.
- Before cutting the material for your project, perform trial cutting with a scrap of the same material.
-
Refer to the Mat and Material Combinations for the redeveloped mats that can be used with your materials.
| Material |
Standard mat |
Low tack adhesive mat |
||
| Paper | Printer paper | 80 g/m² (0.1 mm) |
 |
 |
| Scrapbook paper (thin) | 120 g/m² (0.15 mm) |
|
||
| Scrapbook paper (medium-thick) | 200 g/m² (0.25 mm) |
|
*1 |
|
|
Cardstock (thin) |
200 g/m² (0.25 mm) |
|
*1 |
|
| Cardstock (medium-thick) | 280 g/m² (0.35 mm) |
|
*1 |
|
| Vellum, tracing paper | 0.07 mm | |
||
| Poster board (thin) | 280 g/m² (0.35 mm) |
|
|
|
| Poster board (thick) | 400 g/m² (0.5 mm) |
|
|
|
| All kinds of fabric | *2 |
|||
| Others | Plastic sheet (PP) | 0.2 mm | |
|
| Vinyl | 0.2 mm | |
||
| Magnet | 0.3 mm | |
||
| Sticker or seal | 0.2 mm | |
|
|
*1 When cutting smooth paper
*2 High tack adhesive fabric support sheet is required (depends on fabric type).
Redeveloped mats that can be used with various accessories
Refer to the table below for the redeveloped mats that can be used with your accessories.
The machine operating procedures do not change when redeveloped mats are used.
The accessories that you can purchase may differ depending on your country. For details, contact the retailer who sold you this machine or the nearest authorized service center.
| Part Name | Part Code | Standard mat | Low tack adhesive mat |
| RhineStone Starter Kit | CARSKIT1 | |
|
| Rhinestone Sheet Set | CARSSH1 | |
|
| Rhinestone Transfer Sheet | CARSTS1 | |
|
| Printable Sticker Starter Kit | CAPSKIT1 | |
|
| Printable Sticker Sheet Set | CAPSS1 | |
|
| Mini Printable Sticker Sheet Set | CAPSSMINI1 | |
|
| Stencil Sheet | CASTCL1 | |
|
| Stamp Starter Kit | CASTPKIT1 | |
|
| Stamp Sheets | CASTPS1 | |
|
| Embossing Starter Kit | CAEBSKIT1 | |
|
| Embossing Mat | CAEBSMAT1 | |
|
| Embossing Template Sheets | CAEBSTS1 | |
|
| Foil Transfer Starter Kit | CAFTKIT1 | |
|
| Iron-On Fabric Appliqué Contact Sheet | CASTBL1 | |
|
| High Tack Adhesive Fabric Support Sheet | CASTBL2 | |
