Perform the region emboss initial setting according to the following procedure.
Initial setup for region embossing is done by performing the following operations:
Trial Cutting, Scanning/Cutting Position Adjustment, and Emboss Template Position Adjustment.
Prepare the following.
Size |
12" × 12" (305 mm × 305 mm) size of thick paper that has not been embossed. |
Paper |
Thick paper with one white side |
Thickness |
Thick paper equivalent to 150 g/m2 through 200 g/m2 |
Mat |
Middle tack adhesive mat
The cutting mats used by this machine have been redeveloped with a different design, type, function, etc.
For details, refer to Important information about Mat. |
Blade |
Holder (turquoise) |
-
Recall the pattern you want to emboss.
-
Touch
.
![](/g/b/img/faqend/faqh00100590_000/as_ot/en/1208987/faqh585_fig00002.gif)
-
Select "Region Emboss".
![](/g/b/img/faqend/faqh00100590_000/as_ot/en/1208988/faqh585_fig00003.gif)
-
Select "Create template".
![](/g/b/img/faqend/faqh00100590_000/as_ot/en/1208989/faqh585_fig00004.gif)
-
Touch the "OK" key.
![](/g/b/img/faqend/faqh00100590_000/as_ot/en/1208990/faqh585_fig00005.gif)
Trial Cutting
First, perform trial cutting to check that the prepared materials can be cut.
-
Attach the prepared paper to the middle tack adhesive mat.
Make sure that the white side is facing up when attaching the paper to the mat.
![](/g/b/img/faqend/faqh00100590_000/as_ot/en/1208991/faqh585_fig00006.gif) |
(1) White surface |
When using prepared paper with one colored side, be sure to attach the paper with the white side facing up.
-
Adjust the blade extension according to the paper.
Adjust the blade extension according to the thickness of the prepared paper, such as a setting of 3.5 for 150 g/m2 paper and a setting of 4 for 200 g/m2 paper.
![](/g/b/img/faqend/faqh00100590_000/as_ot/en/1208992/faqh585_fig00007.gif) |
(1)Turn to the left to decrease the blade extension.
(2) Turn to the right to increase the blade extension. |
If too much of the blade is extended, the blade may break or the mat may be cut. When increasing the blade extension, adjust it in increments of half a marking, and then perform trial cutting.
-
Insert the holder into the carriage, and push down on the holder lock lever.
![](/g/b/img/faqend/faqh00100590_000/as_ot/en/1208993/faqh585_fig00008.gif)
-
Adjust the cutting pressure.
When using 150 g/m2 to 200 g/m2 paper, set the cutting pressure to 0.
![](/g/b/img/faqend/faqh00100590_000/as_ot/en/1208994/faqh585_fig00009.gif)
-
Touch the "OK" key.
-
Press
to load the mat with the thick paper, and press Start/Stop button.
-
Touch the "OK" key if the sheet is cut cleanly.
![](/g/b/img/faqend/faqh00100590_000/as_ot/en/1208995/faqh585_fig00010.gif)
If the paper is not cut cleanly, touch the "Cancel" key.
Repeatedly perform trial cutting and adjust the blade extension until the material is cut cleanly.
▲TOP
Scanning/Cutting Position Adjustment
After performing trial cutting to confirm that the material can be cut, follow the procedure below to adjust the scanning/cutting position.
-
Press Start/Stop button to start "Scanning/Cutting Position Adjustment".
-
When the scan of the cut (left) appears, touch the arrow keys to align the center of the red circle with the center of the cut.
![](/g/b/img/faqend/faqh00100590_000/as_ot/en/1208998/faqh585_fig00013.gif)
-
Touch the "Next" key.
![](/g/b/img/faqend/faqh00100590_000/as_ot/en/1208999/faqh585_fig00014.gif)
-
Adjust the right cut in the same way, and then touch the "OK" key.
![](/g/b/img/faqend/faqh00100590_000/as_ot/en/1209000/faqh585_fig00015.gif)
-
When the following message appears, touch the "OK" key.
![](/g/b/img/faqend/faqh00100590_000/as_ot/en/1209001/faqh585_fig00016.gif)
▲TOP
Emboss Template Position Adjustment
-
Press
in the operation panel to feed out the mat.
-
Fold the cut-out embossing adjustment sheet in half, along the dotted line.
Fold the sheet, as shown below, so that the numbers can be read.
![](/g/b/img/faqend/faqh00100590_000/as_ot/en/1209002/faqh585_fig00017.gif)
-
Touch the "OK" key.
-
Overlap
.
Referring to the numbers below the rectangles, select the number for the cutout that is perfectly aligned on the left and right.
![](/g/b/img/faqend/faqh00100590_000/as_ot/en/1209004/faqh585_fig00018.gif)
-
Press the "OK" key.
-
Press the "OK" key.
![](/g/b/img/faqend/faqh00100590_000/as_ot/en/1209005/faqh585_fig00019.gif)
The region emboss initial setting is finished.
Refer to "What should I do if I want to change the initial setting (position adjustment) for region embossing?" if you want to change the setting.
▲TOP