RJ-3250WB

FAQs & Troubleshooting

FAQs & Troubleshooting

How to charge the rechargeable Li-ion battery

Before using the rechargeable Li-ion battery (PA-BT-006), use one of the following methods to charge it.

  • Print speed varies with the available battery power.
  • Be sure to remove the insulated sheet before charging the battery.
The indicator lights as follows to indicate the status of battery charge.
LED indicator Status
Orange Battery is charging.
Off
(when power is turned off)
Green
(when power is turned on)

Battery is fully charged.

 

Disconnect the AC Adapter or car adapter from the battery’s DC connector.

 

Recharging the Battery Using the Battery Charger (Optional: PA-BC-003)

PA-BC-003

1  Charge indicator
2  Battery charging terminals
3  Battery compartment
4  Locking expansion slot
5  DC connector OUT
6  DC connector IN
7  Locking expansion hook
8  DC cord

The AC Adapter (PA-AD-600A), which is sold separately, is required for charging.
To charge the rechargeable Li-ion battery, use the charger together with the AC Adapter (PA-AD-600A).
The Battery Charger (PA-BC-003) cannot recharge the battery alone.

  1. Connect the AC Adapter to the charger’s DC connector IN, and then connect the AC power cord to the AC Adapter.
    Battery charger

    Insert the AC Adapter through the opening in the battery charger as shown in the illustration.
    Install the AC Adapter so the battery charger does not press on it.

  2. Connect the AC power cord to a nearby AC power outlet.
  3. Align the charging terminals of the charger and the battery, and then insert the battery.
    The charge indicator lights in orange when the battery is charging.
  4. The charge indicator will turn off when charging is complete.
    You can then remove the battery.
    Battery charger
[  Back To Top ]

 

Recharging the Battery Using the Single Active Docking Station (Optional: PA-CR-005)

PA-CR-005

1  Docking Station Terminals

2  Ethernet (LAN) LED

3  Charging LED

4  Eject Button

5  Ethernet (LAN) Port

6  DC Connector

7  Docking Station Terminal Attachment

8  Screws (2 each)

  • The AC Adapter (PA-AD-600A, sold separately) can be used for providing power from an AC wall outlet to the Docking Station and charging the battery if installed.
    The Single Active Docking Station (PA-CR-005) cannot recharge the battery alone.
  • The Docking Station can be used without a battery as a power supply.
  • Do not turn on the printer and the Docking Station simultaneously.
  • Sequential printing and the mass storage mode are not supported when the Docking Station is used to print.
  • When the printer is placed on the Docking Station, we recommend using the After one page of data is received (To refresh print status) in the Other tab of the printer driver properties before printing.
  1. Remove the Docking Station terminal cover with a flathead screwdriver.
    Image
  2. Install the Docking Station Terminal Attachment onto the printer using the Docking Station Terminal Attachment and screws included with the Docking Station.

    Make sure the notched corner is aligned correctly.

  3. Connect the AC Adapter to the Docking Station's DC Connector.
    Image
  4. Connect the AC power cord to the AC Adapter.
  5. Connect the AC power cord to a nearby AC power outlet.
  6. Align the Docking Station Terminals of the Docking Station and the printer.
    Image
  7. Press the printer down and onto the Docking Station until the latches lock it firmly in place.
    The printer’s LED Indicator lights in orange when charging.
    The printer’s battery indicator will turn off when charging is complete.
  • If a printer that is performing Wi-Fi® communication and has the wired LAN function turned on is placed on the Docking Station, Wi-Fi will turn off.
  • When the printer is removed from the Docking Station, Wi-Fi will turn on again.
[  Back To Top ]

 

Printer Removal
Push the Eject Button on the back of the Docking Station, and lift the printer and remove it from the Docking Station.

Image

1. Eject Button

 

Lock the Eject Button
Insert a cotter pin (or similar) through the hole as illustrated below.
Image

1. Diameter: 2.3 mm (0.09 in.)
2. Length: 41.2 mm (1.62 in.)
  • Use a Low Carbon Steel Extended Prong Retaining Cotter Pin.
  • Contact your Brother dealer or Brother Customer Service for the cotter pin.

 

Recharging the Battery Using the 4-bay Active Docking Station (Optional: PA-4CR-003)

 

The 4-bay Active Docking Station cannot recharge the printer's battery without being connected to an AC power outlet using the AC adapter (PA-AD-600A).

 

  1. Remove the Docking Station terminal cover with a flathead screwdriver.
    PA-4CR-003
  2. Install the Docking Station Terminal Attachment onto the printer using the Docking Station Terminal Attachment and screws included with the Docking Station.

    Make sure the notched corner is aligned correctly.

  3. Connect the AC Adapter to the Docking Station's DC Connector.
    Image
  4. Connect the AC power cord to the AC Adapter.
  5. Connect the AC power cord to a nearby AC power outlet.
  6. Align the Docking Station Terminals of the Docking Station and the printer.
    Image
  7. Press the printer down and onto the Docking Station until the latches lock it firmly in place.
    The printer’s LED Indicator lights in orange when charging.

    The printer’s LED Indicator will turn off when charging is complete.

[  Back To Top ]

If your question was not answered, have you checked other FAQs?

Have you checked manuals?

If you need further assistance, please contact Brother customer service:

Related Models

RJ-3250WB

Content Feedback

To help us improve our support, please provide your feedback below.

Step 1: How does the information on this page help you?

Step 2: Are there any comments you would like to add?

Please note this form is used for feedback only.