MFC-9460CDN

FAQs & Troubleshooting

FAQs & Troubleshooting

Clean the drum unit

Follow the steps below to clean the drum unit.
NOTE: Illustrations shown below are from a representative product, and may differ from your Brother machine.


DO NOT use cleaning materials that contain ammonia, alcohol, any type of spray, or any type of flammable substance to clean the outside or inside of the machine. Doing this may cause a fire or electrical shock.

DO NOT use any type of flammable substance

  1. Print the drum dot check sheet.
    *If your Brother machine has a touchscreen, please follow the steps under "For touchscreen models" below.

    1. Make sure the machine is in the ready state.
    2. Press Menu.
    3. Press the Up or Down Arrow key to choose Print Reports and press OK.
    4. Press the Up or Down Arrow key to choose Drum Dot Print and press OK.
    5. Press Black (Mono) Start or Color (Colour) Start.
    6. Press Stop/Exit.

    <For touchscreen models>
    1. Make sure the machine is in the ready state.
    2. Press Menu on the LCD screen.
    3. Press the Up or Down Arrow key to display Print Reports. Press Print Reports
    4. Press the Up or Down Arrow key to display Drum Dot Print. Press Drum Dot Print.
    5. Press Black (Mono) Start or Color (Colour) Start.
    6. Press Stop/Exit.

  2. Turn off the machine's power switch. Unplug the telephone line cord first (if applicable), disconnect all cables, and then unplug the power cord from the AC power outlet.

  3. Press the front cover release button and then open the front cover.
    Opening the front cover
  4. Hold the green handle of the drum unit. Pull the drum unit out until it stops.Pulling out the drum unit

  5. Turn the green lock lever (1) at the left of the machine counterclockwise to the release position.
    Turning the green lock lever

  6. Holding the green handles of the drum unit, lift the front of the drum unit and remove it from the machine.
    Removing the drum unit


    • Be careful not to inhale toner.
    • We recommend that you place the drum unit and/or toner cartridge on a clean, flat surface with a piece of disposable paper underneath it in case you accidentally spill or scatter toner.
    • Handle the toner cartridge carefully. If toner scatters on your hands or clothes, wipe or wash it off with cold water at once.
    • Hold the green handles of the drum unit when you carry it. DO NOT hold the sides of the drum unit.
    Holding the green handles

    To prevent damage to the machine from static electricity, DO NOT touch the electrodes shown in the illustration.

    DO NOT touch the electrodes

  7. Hold the handle of the toner cartridge and slightly push it to unlock. Then pull it out of the drum unit. Repeat this for all the toner cartridges.
    Pulling out the toner cartridge

    To avoid print quality problems, DO NOT touch the shaded parts shown in the illustrations.

    DO NOT touch the drum surface

     
  8. Turn the drum unit over by holding the green handles.
    Turning the drum unit over

  9. Make sure that the drum unit gears (1) are on the left hand side.
    Checking the drum unit gear position

  10. Check the drum dot check sheet printed in Step 1.
    • Dot Color problem: The color of printed dots is the color of the drum you should clean.
    • Dot location: The sheet has eight numbered columns. The number of the column with the printed dot in it is used to find the dot position on the drum.
      Checking the drum dot check sheet
  11. Confirm suspected area of the appropriate color drum by using the numbers beside the drum which relate to the numbers of column.
    Confirming suspected area of the drum

  12. Turn the drum unit gear toward you by hand while looking at surface of the suspected area.
    Looking at surface of the suspected area

  13. When you have found the mark on the drum that matches the drum dot check sheet, wipe the surface of the drum gently with a cotton swab until the mark on the surface comes off.
    Wiping the surface of the drum


    DO NOT clean the surface of the photosensitive drum with a sharp object.

  14. Hold the handle of the toner cartridge and slide it into the appropriate colored section of the drum unit until it clicks into place.
    Sliding the toner cartridge into the drum unit

  15. Make sure the green lock lever (1) is in the release position as shown in the illustration.
    Checking the green lock lever position


  16. Match the guide ends (2) of the drum unit to the Arrow mark marks (1) on both sides of the machine, then gently slide the drum unit into the machine until it stops at the green lock lever.
    Sliding the drum unit

  17. Turn the green lock lever (1) clockwise to the lock position.
    Turning the green lock lever

  18. Push the drum unit in until it stops.
    Pushing the drum unit in

  19. Close the front cover of the machine.

  20. Plug the machine's power cord back into the AC power outlet first, connect all cables, and then plug in the telephone line cord (if applicable). Turn on the machine's power switch.

If your question was not answered, have you checked other FAQs?

Have you checked the manuals?

If you need further assistance, please contact Brother customer service:

Related Models

MFC-9460CDN, MFC-9970CDW

Content Feedback

To help us improve our support, please provide your feedback below.

Step 1: How does the information on this page help you?

Step 2: Are there any comments you would like to add?

Please note this form is used for feedback only.