Innov-is 1500D/1500

FAQs & Troubleshooting

FAQs & Troubleshooting
  • Date: 07/11/2016
  • ID: faqh00000469_000

How do I thread my machine (Threading the upper thread)?

  • The machine is marked with numbers that indicate the threading order. Follow the numbers in order.
  • Be sure to thread the machine properly. Improper threading can cause the thread to tangle and break the needle, leading to injury.
  • When using accessories not included with this machine, attach the accessory to the machine after threading the machine.
  • Never use the thread of No. 20 or lower.

 

  1. Turn on the machine.
    Turn on the machine.
     
  2. Press the "Presser Foot Lifter" button to raise the presser foot.
    The upper thread shutter opens so the machine can be threaded.
    Press the "Presser Foot Lifter" button to raise the presser foot. 1 Upper thread shutter
     

     

    This machine is equipped with an upper thread shutter, allowing you to check that the upper threading is performed correctly.

     

  3. Press the "Needle Position" button to raise the needle.
    Press the "Needle Position" button to raise the needle.

     

    If you try to thread the needle with the needle threader lever without raising it, damage to the machine may result.

     

  4. Pick up the spool pin and remove the spool cap that is inserted onto the spool pin.
    Pick up the spool pin and remove the spool cap that is inserted onto the spool pin. 1 Spool pin

    2 Spool cap
     

     

  5. Place the spool of thread onto the spool pin.
    Slide the spool onto the pin so that the spool is horizontal and the thread unwinds to the front at the bottom.
    Place the spool of thread onto the spool pin.
     
  6. Slide the spool cap onto the spool pin and return the spool pin to its original position.
    Slide the spool cap as far as possible to the right as shown, with the rounded side on the left.
    Slide the spool cap onto the spool pin and return the spool pin to its original position.
     
    • If the thread spool and/or spool cap are set incorrectly, the thread may tangle on the spool pin and cause the needle to break.
    • Use the spool cap (large, medium, or small) that is closest in size to the thread spool. If a spool cap smaller than the thread spool is used, the thread may become caught in the slit on the end of the spool and cause the needle to break.
    • When sewing with fine, cross-wound thread, use the small spool cap, and leave a small space between the cap and the thread spool.
      When sewing with fine, cross-wound thread 1 Spool cap (small)

      2 Thread spool (cross-wound thread)

      3 Space

     

  7. While holding the thread from the spool with both hands, pull the thread through the lower notch in the thread guide plate, then through the upper notch.
    Pull the thread through the lower notch in the thread guide plate, then through the upper notch. 1 Lower notch in the thread guide plate

    2 Upper notch in the thread guide plate

     

    When passing the thread through the lower notch in the thread guide plate, then through the upper notch, be sure to use both hands. If you do not hold the thread with your right hand, the thread will be loose and you cannot hang the thread on the thread guide plate correctly. It may cause incorrect thread tension.

     

  8. While holding the thread from the spool in your right hand, hold the end of the thread with your left hand, and then guide the thread through the groove, following the arrows in the illustration.

    Guide the thread through the groove.
     
  9. Pass the thread through the guides in the order shown below.
    Pass the thread through the guides in the order shown below. 1 Upper thread shutter

     

    Look through the take-up lever check window to check the position of the take-up lever. Before threading the machine, make sure that the take-up lever is in the raised position.
    Make sure that the thread is passed into the thread take-up lever as shown below.

    Look through the take-up lever check window to check the position of the take-up lever. 1 Upper thread shutter

    2 Thread take-up lever check window
     

     

  10. Pass the thread behind the needle bar thread guide.
    The thread can easily be passed behind the needle bar thread guide by holding the thread in your left hand, then feeding the thread with your right hand, as shown.
    Pass the thread behind the needle bar thread guide. 1 Needle bar thread guide

 

Related FAQs

If your question was not answered, have you checked other FAQs?

Have you checked the manuals?

If you need further assistance, please contact Brother customer service:

Related Models

Innov-is 1500D/1500, Innov-is 2500D, Innov-is 2800D, QC-1000

Content Feedback

To help us improve our support, please provide your feedback below.

Step 1: How does the information on this page help you?

Step 2: Are there any comments you would like to add?

Please note this form is used for feedback only.

Submit