SDX135PRO

FAQs & Troubleshooting

FAQs & Troubleshooting

The Material to be Cut is Not Cleanly Cut with the Roll Feeder.

When the material to be cut is not cleanly cut with the roll feeder, check the following problem and perform the necessary operation according to each solution.

 

Problem 1 : The entire pattern cannot be cut. / Not all of the material to be cut is cut. Some areas remain uncut.
Problem 2 : There are deep cuts completely through the backing paper of the material.  
Problem 3 : The material being cut catches on the tip of the blade.
Problem 4 : The machine stopped while an operation is being performed, and an error message was appeared.

 

 

 

 

Problem 1 : The entire pattern cannot be cut. / Some areas remain uncut.


Solution 1

 

Check that the auto blade holder (Black) is installed into the machine.
If the thin fabric auto blade (Beige) is installed, replace it with the auto blade holder (Black).

 

 

 

Solution 2

 

The cutting pressure may be too light.

Touch image  in the settings screen once to increase the Cut Pressure (Half Cut), and then try again.

image image image

 

Before making your project, perform test/trial cut with the same material.
For details, refer to How Do I Perform Trial Cutting for Roll Feeder? (Test Cut).
 

  • Be careful not to increase the pressure too much. Otherwise, the blade may break. If the pressure is too strong, the material may not be cut cleanly.
  • If the blade penetrates the material, faint cut marks may remain on the machine's surface where the blade makes contact (1). In that case, cutting may no longer be performed correctly. Contact Brother Customer Service or Brother authorized service center.
    image (1) Blade makes contact

 

 

 

Solution 3

 

Check that the blade is loose.
If it is loose, turn the cap to the right to tight it securely.
 

image

 

 

 

Solution 4

 

If material cuttings, lint or dust accumulate in the holder, it may not operate correctly. Clean the holder after every use.
For details, refer to Care and Maintenance (Cleaning the Holder) and Care and Maintenance (Cleaning Inside the Machine).

 

 

 

【 If a material still cannot be cut cleanly even though you tried the above operation 】

The blade may be worn. Replace the blade with a new one.

 

▲TOP

 

 

 

 

 

Problem 2 : There are deep cuts completely through the backing paper of the material.

 

The cutting pressure may be too strong.
Decrease the cutting pressure by touching image in the settings screen, and then perform the test/trial cut.
 

image image image

 

After the test pattern can be cut successfully, cut your project.
For details, refer to How Do I Perform Trial Cutting for Roll Feeder? (Test Cut).

 

  • Be careful not to increase the pressure too much. Otherwise, the blade may break. If the pressure is too strong, the material may not be cut cleanly.
  • If the blade penetrates the material, faint cut marks may remain on the machine's surface where the blade makes contact (1). In that case, cutting may no longer be performed correctly. Contact Brother Customer Service or Brother authorized service center.
     
    image (1) Blade makes contact

 

▲TOP

 

 

 

 

Problem 3 : The material being cut catches on the tip of the blade.


Solution 1

 

If material cuttings, lint or dust accumulate in the holder, it may not operate correctly.
Clean the holder and inside the machine after every use.

For details, refer to Care and Maintenance (Cleaning the Holder) and Care and Maintenance (Cleaning Inside the Machine).
 

 

 

 

Solution 2

 

Check that the material being cut is compatible with this machine.
For details on the compatible material, refer to Mat, Cutting Blade and Material Combinations.

 

 

 

 

Solution 3

 

The blade may be worn.
Replace the blade with a new one. 

 

▲TOP

 

 

 

 

 

Problem 4 : The machine stopped while an operation is being performed, and an error message was appeared.

Perform the necessary operation according to the instructions in the message or refer to Error messages section.
 

 

▲TOP

 

 

If your question was not answered, have you checked other FAQs?

Have you checked the manuals?

If you need further assistance, please contact Brother customer service:

Related Models

SDX125, SDX125e, SDX125e Titanium, SDX125i, SDX125TS, SDX135PRO, SDX225, SDX225F, SDX230D, SDX230Di, SDX230DX, SDX325, SDX330D, SDX85, SDX85C, SDX85M, SDX85S

Content Feedback

To help us improve our support, please provide your feedback below.

Step 1: How does the information on this page help you?

Step 2: Are there any comments you would like to add?

Please note this form is used for feedback only.