SB1000T

FAQs & Troubleshooting

FAQs & Troubleshooting
  • Date: 05/07/2015
  • ID: faqh00000580_005

How do I install the bobbin wound with thread? (For models equipped with the quick-set bobbin)

 

  • Winding the bobbin improperly may causethe thread tension to loosen, breaking the needle and resulting in injury.
    image

     

  • The bobbin was designed specifically for this sewing machine. If bobbins from other models are used, the machine will not operate correctly. Use only the enclosed bobbin or bobbins of the same type (part code: SA156, SFB).
    image

    (1) This model

    (2) Other models

    (3) 11.5 mm (approx. 7/16 inch)
  1. Press image (needle position button) to raise the needle to its highest position.
    image
  2. Raise the presser foot lever.
    image (1) Presser foot lever
  3. Turn off the sewing machine.

     

    Turn off the sewing machine.

     

  4. Slide the button and open the cover.
    Slide the button and open the cover.

    (1) Cover

    (2) Slide button

     

  5. Hold the bobbin with your right hand with the thread unwinding to the left, and hold the end of the thread with your left hand. Then, with your right hand, place the bobbin in the bobbin case.

    image

     

  6. Lightly hold down the bobbin with your right hand (A), and then guide the end of the thread around the tab of the needle plate cover with your left hand (B).
    image (1) Tab

    Be sure to hold down the bobbin with your finger and unwind the bobbin thread correctly, otherwise the thread may break or the thread tension will be incorrect.

     

  7. While lightly holding down the bobbin with your right hand (A), guide the thread through the slit in the needle plate cover (B) and lightly pull it with your left hand (C).
    image

     

  8. While lightly holding down the bobbin with your right hand (A), continue guiding the thread through the slit with your left hand (B) Then, cut the thread with the cutter (C).

     

    image 

     

    If the thread is not correctly inserted through the tension-adjusting spring of the bobbin case, it may cause incorrect thread tension.

    image (1) Tension-adjusting spring

     

  9. Replace the bobbin cover. Put the left tab in place (see arrow A), and then press lightly on the right side (see arrow B) until the cover clicks into place.

     

    image

If your question was not answered, have you checked other FAQs?

Have you checked the manuals?

If you need further assistance, please contact Brother customer service:

Related Models

BX2925PRW, CE8100, CP2410, CP-6500, CP-7500, CS-6000/6000b/6000t/6000i, CS7000i, CS7130, CS7205, CS9100, DZ2400, DZ2750, DZ3000, DZ3400, HC1850, HC3010, HC7140, HS-2500, HS-3000, PS300T, QB9110L, SB1000T, SB700T, SC3000, SC9500, SM8270, SQ-9000, SQ9050, SQ9100, SQ9130, SQ9185, SQ9285, SQ9310, XR1300, XR1355, XR3140, XR3240, XR3340, XR-7700, XR-9000, XR9500PRW, XR9550/XR9550PRW, XS2070, XS2080, XS2100, XS3109

Content Feedback

To help us improve our support, please provide your feedback below.

Step 1: How does the information on this page help you?

Step 2: Are there any comments you would like to add?

Please note this form is used for feedback only.

Submit