XS6070

FAQs & Troubleshooting

FAQs & Troubleshooting

How do I thread my machine? (For models equipped with the needle threader)

  • When threading the upper thread, make sure that you thread the machine properly. If the upper threading is not correct, the thread could tangle and the needle may bend or break.
  • Never use a thread weight of 20 or lower.
  • Use the needle and the thread in the correct combination. For details on the correct combination of needles and threads, refer to "Combination of fabric, thread and needle".

img01

[1] Preparing for threading

  1. Turn off the machine.
    img02

    Before threading the needle, be sure to turn off the machine. If you accidentally step on the foot controller and the machine starts to sew, you could be injured.

  2. Raise the presser foot lever to raise the presser foot.
    img03

  3. Raise the needle to its highest position by turning the handwheel toward you (counterclockwise).
    img04
    (1) Turn toward you so that this mark points up to the highest position.

[2] Threading the upper thread

  1. Pull up the spool pin as far as possible, and then put a spool of thread on this pin.
    img05
    * Make sure that the thread unwinds as shown.

  2. While holding the thread from the spool with your right hand, pass the thread toward you, in the groove on the thread guide.
    img06
    (1) Thread guide (2) Spring

    * Make sure that the spring in the groove catches the thread.
     

  3. Feed the upper thread as shown in the following illustration.
    img07
    (1) Thread take-up lever
    * Make sure you guide the thread through the thread take-up lever from right to left as shown in the following illustration.
     

  4. Slide the thread behind the needle bar thread guide.
    img08
    (1) Needle bar thread guide

[3] Threading the needle

  • The needle threader can only be used with home sewing machine needles size 75/11- 100/16. If you are using transparent nylon monofilament thread, you can only use needles in the range of 90/14-100/16.
  • You cannot use the needle threader if you are using decorative threads or special needles, such as the twin needle and wing needle. If you are using those types of threads or needles, thread the eye of the needle by hand. For details, refer to "Threading the needle manually (without using the needle threader)".
  • Make sure the main power switch is off when threading the needle.
  1. Lower the presser foot lever.
    img09
  2. While lowering the needle threader lever fully img10 , hook the thread onto the guide img11 .
    img12

  3. Push back the needle threader lever until it stops img13 , and pass the thread in front of the needle. Make sure that the thread is under the hook that has come through the eye of the needle and the hook catches the thread img14 .
    img15

  4. Return the needle threader lever to the front slowly img16 , and then release the lever slowly.
    img17

  5. Carefully pull the loop of the thread through the eye of the needle to pull out the end of the thread.
    img18

  6. Raise the presser foot lever.
    img19

  7. Pass the end of the thread through and under the presser foot, and then pull out about 10 cm (approx. 4 inches) of thread toward the rear of the machine.

    img20 (1) 10 cm (4 inches)

     


 

 

Threading the needle manually (without using the needle threader)

When using specialty thread, such as transparent nylon thread, a wing needle or a twin needle which cannot be used with the needle threader, thread the needle as described below.

Make sure the main power switch is off when threading the needle.

  1. Thread the machine to the needle bar thread guide.
    For details, refer to "[1] Preparing for threading" and "[2] Threading the upper thread".
     
  2. Insert the thread through the eye of the needle from front to back.
    img21
  3. Pass the end of the thread through and under the presser foot, and then pull out about 10 cm (approx. 4 inches) of thread toward the rear of the machine.
    img22 (1) 10 cm (4 inches)

If your question was not answered, have you checked other FAQs?

Have you checked the manuals?

If you need further assistance, please contact Brother customer service:

Related Models

CE1010, CE1150, CE6080T, CE6085T, CE7700, CP2160F, CP2160L, CP2160M, CP2160P, CP2160R, CP2160W, CP60X, CP80X, CS5055, SH7700, XS6070

Content Feedback

To help us improve our support, please provide your feedback below.

Step 1: How does the information on this page help you?

Step 2: Are there any comments you would like to add?

Please note this form is used for feedback only.