MFC-7860DW

FAQs & Troubleshooting

FAQs & Troubleshooting

Print on envelopes, labels, or thick paper from the manual feed slot.

The machine is equipped with a manual feed slot where envelopes, labels, and thick paper can be manually fed one at a time. The paper tray is for plain paper, recycled paper, and thin paper only. When printing with the back cover open, the machine has a straight paper path from the manual feed slot through to the back of the machine.

 

Envelopes, labels and thick paper can be fed from the manual feed slot only. Do not use the paper tray.

Paper Weight

  • Plain paper: 20-28lbs (75-105g/㎡)
  • Thin paper : 16-20lbs (60-75g/㎡)
  • Thick paper: 28-43lbs (105-163g/㎡)
 

Follow the steps below to print on envelopes, labels, or thick paper.

NOTE: Illustrations shown below are from a representative product and may differ from your Brother machine.

  1. Open the back cover (back output tray).
    Open the back cover
  2. Do one of the following.

     

  3. For printing envelopes only:
    Pull down the two green levers, one on the left-hand side and one on the right-hand side.
    Pull down the two green levers.

     

     

  4. Open the manual feed slot cover on the front of the machine.
    Open the manual feed slot cover.

     

  5. Using both hands, slide to the width of the paper, envelope, or label sheet that you are going to use.

    Set the manual feed slot paper guides.

     

  6. Using both hands, put one sheet of paper, one envelope, or one full sheet of labels in the manual feed slot until the front edge touches the paper feed roller.
     

    DO NOT insert labels that have previously been used or that have some labels missing from the sheet. It may cause serious jams and the damage to your Brother machine.

     

     

    Put paper or envelope.

     

     

    Once the machine has grasped the paper, envelope, or label sheet, let go. The machine will hold the paper, envelope, or label sheet in place until the print data is sent to the machine.
    Image 2
    • Put the side to be printed on face up.
    • Make sure the paper, envelope, or label sheet is straight and in the proper position in the manual feed slot. If it is not, it may not feed properly resulting in a skewed printout or a paper jam.
    • Do not put more than one sheet of paper, one envelope, or one label sheet in the manual feed slot at a time, as it may cause a jam.
    • If you put a sheet of paper, an envelope, or a label sheet in the manual feed slot before the machine is in Ready mode, it may be ejected without being printed on.

     

     
  7. Select the appropriate Paper Size and Media Type for the paper, envelope, or label sheet in the printer driver. 
     
    • Remove each sheet of paper, envelope, or label sheet as soon as it has been printed. Stacking them may cause a jam or curl.
    • If envelopes are smudged during printing, set the Media Type to Thick Paper or Thicker Paper to increase the fixing temperature.
     

     

  8. Send the print data to the machine.
     
  9. After the paper, envelope, or label sheet comes out of the machine, put in the sheet of paper, envelope, or full label sheet.
     
  10. When you have finished printing, do one of the following.

     

  11. For printing envelopes only:
    Reset the two green levers that were pulled down in STEP 2 back to their original position.
    Reset the two green levers that were pulled down.

     

  12. Close the back cover (back output tray).
    Close the back cover.

If your question was not answered, have you checked other FAQs?

Have you checked the manuals?

If you need further assistance, please contact Brother customer service:

Related Models

DCP-7055, DCP-7055W, DCP-7060D, DCP-7065DN, HL-2280DW, MFC-7360N, MFC-7365DN, MFC-7460DN, MFC-7860DW

Content Feedback

To help us improve our support, please provide your feedback below.

Step 1: How does the information on this page help you?

Step 2: Are there any comments you would like to add?

Please note this form is used for feedback only.