Innov-is 6700D

FAQs & Troubleshooting

FAQs & Troubleshooting

When I sew an embroidery pattern design exported as DST format in PE-DESIGN, how do I specify whether or not the jump stitches are cut on the embroidery machine of the Innov-is series?

When the embroidery pattern design is exported as DST format in PE-DESIGN, regardless of the value in the Number of jumps for trim box, you can specify whether or not the jump stitches are cut on the embroidery machine of the Innov-is series.

 

Refer to "Related Models" about target models of the Innov-is series.

 

 

navi When cutting the upper and bobbin thread before the jump stitch

navi When not cutting the upper and bobbin thread before the jump stitch

navi When selecting the length of the jump stitch

 

 

  • When cutting the upper and bobbin thread before the jump stitch

    The thread trimming function Jump stitch key will automatically trim any excess thread jumps within the color. This function is initially turned on.

 

 

  • When not cutting the upper and bobbin thread before the jump stitch

    To turn this function off, press Cut/Tension key key and then Jump stitch key. This function can be turned on or off during embroidering.


    Jump stitch 1 Jump stitch
     
    • Your customized setting remains after turning off and on the machine.
    • When this function is turned on, use the enclosed ball point needle 75/107 for embroidering patterns with short jump stitches such as alphabet characters. Using other needles may cause the thread to break.
     
    1. Press Cut/Tension key.
      Press the Cut/Tension key.

       
    2. Press Jump stitch key to turn off JUMP STITCH TRIM.
      Press the Jump stitch key to turn off JUMP STITCH

      The key will display as Jump stitch key.

    The machine will not trim the thread before moving to the next stitching.

top top


 

 

  • When selecting the length of the jump stitch

    When the thread trimming function Jump stitch key is turned on, you can select the length of the jump stitch not to trim the thread. This function can be turned on or off during embroidering.
    Select a setting from 5 mm to 50 mm in 5 mm increments.
    Your customized setting remains after turning off and on the machine.
    Press plus key or minus key to select the length of JUMP STITCH.

    For example: Press plus key to select 25 mm (1 inch) and the machine will not trim a jump stitch of 25 mm or less before moving to the next stitching.

     

    Press the plus key.

     
    • If design has many trims it is recommended to select a higher jump stitch trim setting in order to reduce the amount of excess tails on backside of fabric.
    • The higher number of the jump stitch length selected, the fewer number of times the machine will trim. In this case, more jump stitches remain on the surface of the fabric.
     
 

If your question was not answered, have you checked other FAQs?

Have you checked the manuals?

If you need further assistance, please contact Brother customer service:

Related Models

Innov-is 4000D/4000, Innov-is 4500D, Innov-is 4750D, Innov-is 6000D, Innov-is 6700D, Innov-is 6750D, Innov-is BP2100, Innov-is BP2150L, Innov-is VE2200, Innov-is VE2300, Innov-is VM5100, Innov-is VM5200, Innov-is VM6200D, PE-DESIGN 10, PE-DESIGN 11, PE-DESIGN 8, PE-DESIGN NEXT, PE-DESIGN Ver.7

Content Feedback

To help us improve our support, please provide your feedback below.

Step 1: How does the information on this page help you?

Step 2: Are there any comments you would like to add?

Please note this form is used for feedback only.