Adjusting the Blade Extension

The appropriate blade extension differs depending on the material type and thickness. Before installing the holder in the carriage, turn the holder cap to adjust the blade extension, and then perform trial cutting.

 

Cutting Settings

 

Use the following table to select the appropriate settings according to the material that will be cut.

 

Material and its thickness

Blade scale setting

Cut pressure setting

Cutting blade
Standard cut blade

(turquoise)

Deep cut blade

(purple)

Paper

Printer paper

80 g/m²
(0.1 mm)

3 -1 -

Scrapbook paper
(thin)

120 g/m²
(0.15 mm)

3.5 0 -
Scrapbook paper
(medium-thick)
200 g/m²
(0.25 mm)
4 0 -
Cardstock (thin) 200 g/m²
(0.25 mm)
4 0 -

Cardstock
(medium-thick)

280 g/m²
(0.35 mm)

5 0 -
Vellum, tracing paper 0.07 mm 3 0 -
Poster board (thin) 280 g/m²
(0.35 mm)
5.5 0 -
Poster board (thick) 400 g/m²
(0.5 mm)
7.5 4 -
Fabric

Thin cotton fabric

(for quilt piece)

0.25 mm 4 4 -

Thin cotton fabric
(except
for quilt piece)

0.25 mm 4 4 -

Flannel (for quilt piece)

0.6 mm

6.5 4 -

Flannel
(except for quilt piece)

0.6 mm

6.5 4 -

Felt

1 mm

5 5 -

Denim 14 oz

0.75 mm 5.5 6 -
Others Plastic sheet (PP) 0.2 mm 4 0 -

Vinyl

0.2 mm

4 0 -
Adhesive Craft Vinyl
(backing sheet : 0.1 mm)
0.07 mm 1.5 * -1 -
Magnet 0.3 mm 5.5 0 -

Sticker or seal

0.2 mm 4 0 -
Sticker Sheet
(backing sheet : 0.15 mm)
0.15 mm 2 * -1 -

* Half cut

 

  • Adjust the setting for “Cut Pressure” in the settings screen. For details, see "About DesignNCut Manager ".
  • Use a high tack adhesive fabric support sheet or a iron-on fabric appliqué contact sheet when you cut a piece of fabric out.
    For details, see "Mat and Material Combinations".

 

The settings indicated in the table are approximations. The setting will differ depending on the type and thickness of the material to be cut. Be sure to perform a trial cutting first.

 

 

Appropriate Blade Extension

 

Adjust the blade extension to slightly exceed the thickness of the material that will be cut. Use the markings on the holder to make the adjustment.

img (1) End of holder cap
(2) Material that will be cut
(3) Length of blade tip

Be careful that the blade does not extend too much. The blade can cut even though it only slightly extends from the holder. If too much of the blade extends, it may break.

 

 

Adjusting the Cutting Blade

 

  1. Remove the protective cap.

    After use, be sure to retract the blade into the holder and attach the protective cap.

     

     

    image

    Do not allow infants/children to put the protective caps in their mouths.

     

  2. With the reference line on the holder facing toward you, fully turn the cap to the right to extend the blade tip to its maximum.
    img (1) Reference line
    (2) Extend the blade tip to its maximum.
  3. Check the thickness of the material, and then adjust the blade extension. See “Cutting Settings”
    img (1) Turn to the left to decrease the blade extension.
    (2) Turn to the right to increase the blade extension.

     

If your question was not answered, have you checked other FAQs?

Have you checked the manuals?

If you need further assistance, please contact Brother customer service:

Related Models

DC200, DC200ULE

Content Feedback

To help us improve our support, please provide your feedback below.

Step 1: How does the information on this page help you?

Step 2: Are there any comments you would like to add?

Please note this form is used for feedback only.