HS-2000

FAQs & Troubleshooting

FAQs & Troubleshooting
  • Date: 05/14/2015
  • ID: faqh00000467_003

How do I thread my machine? (Threading the needle manually [without using the needle threader])

When using special threads, the wing needle or the twin needle which cannot be used with the needle threader, thread the eye of the needle by hand as described below.

 

Upper threading

1 Spool pin      2 Thread guide      3 Mark on the handwheel

 

Make sure you thread the machine properly. Otherwise, the thread could tangle and break the needle.

 

 

1. Raise the presser foot using the presser foot lever.

Raise the presser foot using the presser foot lever 1 Presser foot lever

 

If the presser foot is not raised, the sewing machine cannot be threaded.

 
2. Raise the needle by turning the handwheel toward you (counterclockwise) so that the mark on the wheel points up, or press needle position button (for models equipped with the needle position button) once or twice to raise the needle.

Raise the needle by turning the handwheel toward you
  1 Mark on the handwheel      2 Needle position button

 

If the needle is not correctly raised, the sewing machine can not be threaded.
Be sure to turn the handwheel so that the mark on the wheel points up before threading the sewing machine.

 
3. Turn off the sewing machine.

Turn off the sewing machine

 
4. Pull up the spool pin as far as possible, and then put a spool of thread on this pin.

Pull up the spool pin and put a spool of thread on the pin

 

If the spool of thread is in the wrong place, or is set incorrectly, the thread may tangle on the spool pin and cause the needle to break.

 
5. Feed the upper thread as shown in the illustration below;
  i) Pass the thread through the thread guide.
 ii) Guide the thread down and up through the groove.

Feed the upper thread as shown in the illustration  1 Thread guide

 
6. Pass the thread into the thread take-up lever from the right to the left.
Then guide the thread down through the groove.
Pass the thread into the thread take-up lever
  1 Thread take-up lever

 

 
  • If the thread take-up lever is lowered, the upper thread cannot be wrapped around the thread take-up lever. Make sure you raise the presser foot lever and the thread take-up lever before you feed the upper thread.
  • If you incorrectly feed the thread you may cause sewing problems.
 
7. Put the thread behind the needle bar thread guide above the needle.

Put the thread behind the needle bar thread guide
  1 Needle bar thread guide

 

The thread can easily be passed behind the needle bar thread guide by holding the thread in your left hand, then feeding the thread with your right hand.

 
8. Pass the thread through the eye of the needle from front to back.
Pass the thread through the eye of the needle from front to back 

 
9. Pass the end of the thread through the presser foot, and then pull out about 5 cm (2 inches) of thread toward the rear of the machine.
Pass the end of the thread through the presser foot, and then pull out about 5 cm (2 inches)

Related FAQs

If your question was not answered, have you checked other FAQs?

Have you checked the manuals?

If you need further assistance, please contact Brother customer service:

Related Models

BX2925PRW, CE-5000/5000PRW, CS-100T/4000/5000H, CS-6000/6000b/6000t/6000i, CS9100, ES-2000/2000T, EX-660, HS-2000, HS-3000, SB700T, SQ-9000, SQ9050, XR-7700, XR-9000, XR9500PRW

Content Feedback

To help us improve our support, please provide your feedback below.

Step 1: How does the information on this page help you?

Step 2: Are there any comments you would like to add?

Please note this form is used for feedback only.

Submit