How do I load the spool into the thread cassette?

When threading the upper thread, carefully follow the instructions.
If the upper threading is not correct, the thread may become tangled or the needle may bend or break.

The order for threading the thread cassette is indicated on the thread cassette.
Also check the markings on the thread cassette while threading it.

 

  1. Turn on the sewing machine.

    Open the thread cassette compartment cover at the top on the left side of the machine.

    Open the thread cassette compartment cover

     

  2. Push the thread cassette eject lever on the left side of the machine toward the back.
    If the sewing machine is turned off, the thread cassette will not be ejected correctly.
    Push the thread cassette eject lever 1 Thread cassette eject lever

    The thread cassette is raised.

    Check that the sewing machine is turned on.
    If the sewing machine is turned off, the thread cassette will not be ejected correctly.

     

  3. Remove the thread cassette.

    Remove the thread cassette.

     

  4. Pull the cover of the thread cassette out toward you, and then pull off the spool cap that is inserted onto the spool pin.
    Pull the cover of the thread cassette out toward you. 1 Spool cap(orange)

    2 Spool pin

    3 Cover

     

  5. Place the spool for the upper thread onto the spool pin.
    Slide the spool onto the spool pin so that the thread unwinds from the left, as seen from the top.
    Place the spool for the upper thread onto the spool pin. 1 Spool

    Check that the thread unwinds from the left as described above.

     

  6. Slide the spool cap onto the spool pin.
    With the rounded side of the spool cap positioned toward the top, slide the spool cap onto the spool pin as far as possible until the down side of the spool touches the down end of the spool pin.

    Slide the spool cap onto the spool pin.

    • Only the orange spool cap should be placed on the spool pin in the thread cassette.
    • If the spool or the spool cap is not positioned correctly, the thread may become tangled around the spool pin or the needle may break.

     

  7. While holding the end of the thread with your right hand and the thread cassette with your left hand, close the cover.
    Close until it clicks. 1 Close until it clicks.

     

    Close until it clicks.

     

  8. Pass the thread through the slit in the top of the thread cassette.
    Follow arrow 2 indicated on the thread cassette.

    Pass the thread through the slit in the top of the thread cassette.

     

  9. Pull the thread to the left and pass it through the slit along the left side of the thread cassette.
    Follow arrow 3 indicated on the thread cassette.

    Pull the thread to the left and pass it through the slit along the left side of the thread cassette.

    When using special thread such as metallic thread, use the thumb of your left hand to lightly press down on the area indicated in the illustration to create an opening that allows for easier threading.

    When using special thread such as metallic 1 Push

    2 Gap

     

  10. Pass the thread along the bottom of the thread cassette.
    Follow arrow 4 indicated on the thread cassette.

    Pass the thread along the bottom of the thread cassette.

     

  11. Pass the thread through the notch in the lower-right corner of the thread cassette, and then pull the thread to the left.
    Follow arrow 5 indicated on the thread cassette.
    Pass the thread through the notch in the lower-right corner of the thread cassette 1 Notch

     

  12. Pull the thread under the disc at the front in the lower-left corner and around to the right, and then the thread will be cut with the cutter.
    Follow arrow 6 indicated on the thread cassette.
    Pull the thread under the disc at the front in the lower-left corner and around to the right. 1 Disc

    2 Cutter

    The spool of thread is now loaded in the thread cassette.

    Be sure the thread is cut as described above,otherwise the needle threader cannot be used to thread the needle.

 

If your question was not answered, have you checked other FAQs?

Have you checked the manuals?

If you need further assistance, please contact Brother customer service:

Related Models

CS-80, CS-8060, CS-8150, HE-120, Innov-is 500D, SE-270D

Content Feedback

To help us improve our support, please provide your feedback below.

Step 1: How does the information on this page help you?

Step 2: Are there any comments you would like to add?

Please note this form is used for feedback only.