The pattern to be scan is not cleanly scanned

 

When the pattern to be cut is not cleanly scanned, check the following problem and perform the necessary operation according to each solution.

 

Problem 1: Unnecessary dots and lines are scanned. The line printed on the mat is scanned.
Problem 2: Some of the lines or images are not converted to cutting lines.
Problem 3: The scanned image is red.
Problem 4: The scan image is out of focus.
Problem 5: When converting the patterns to cutting data, [Cannot operate when there are too many patterns.] message appeared.

 

 

Problem 1: Unnecessary dots and lines are scanned. The line printed on the mat is scanned.

 

Solution 1

 

The scanner glass may be dirty. Clean the scanner glass inside the machine. For details, refer to Care and Maintenance (Cleaning the Scanner Glass).

 

 

 

Solution 2


The original to be scanned is dirty or scratched.

In [Direct Cut] or [Scan to Cut Data] mode, remove thin lines or dirt in the image editing screen. Edit the scanned image according to the following procedure.

 

  1. Touch the [Ignore Object Size] in the image trim screen after scanning the material.
     
    [Direct Cut] mode or [Scan to Cut Data] mode

    image

      image


     
  2. Specify an object size smaller than which is not to be converted to cutting lines, and then touch the [OK].
    The image smaller that the specified size is not converted to cutting lines.

    image



    In Grayscale recognition mode, the image detection level (light, medium, dark) can be set by selecting the image in the image trim screen.
    When setting to [dark], only the scanned dark image is recognized, and if it is set to [light], the scanned light image is also converted to the cutting line.

     image
    image

     
  3. When changing the settings are finished, touch the [OK].


     
  4. Check the image to be cut on the preview screen.

▲ TOP

 

 

 

Problem 2: Some of the lines or images are not converted to cutting lines.

 

Solution 1


The following pattern may not be able to convert to the desired cutting line.

- Patterns that are clearly drawn, with no gradation, fading or blurriness.
- Not using an extremely intricate design.
- The color of the pattern and the background are similar.
- The outline of the pattern is broken.

 


image

 

 

 

 

Solution 2

 

Set the scanner lever position on the left of the machine to "1".

image


 

 

 


Solution 3

 

If a small pattern such as a dot or a line has not been converted to a cut line when scanning in [Direct Cut] or [Scan to Cut Data] mode, check the [Ignore Object Size]. If the size setting of the [Ignore Object Size] is larger than the pattern that could not be converted, reduce the size setting. For details on adjustment of [Ignore Object Size], refer to "Solution 2" in the "Problem 1".


 


Solution 4

 

It may be improved by changing the [Recognition mode]. Change the [Recognition mode] according to the following procedure.
 

 

  1. Select the Scan mode.

    image


     
  2. After selecting the cutting data destination, touch image.

    image

     
     
  3. Select image(Color recognition mode), and then touch [OK].

    image

    Try to scan the material again.



Examples of illustrations appropriate for grayscale recognition mode:

Example Result
Outlines that are clear image image

Distinct difference in brightness between background and illustration

image

 

Scanning in grayscale recognition mode is most appropriate for illustrations with clear outlines or distinct brightness differences. Processing is faster with this mode compared with the color recognition mode. If there are adjacent objects of the same color after an illustration has been converted to grayscale, select the [Color recognition mode].

 

 

Examples of illustrations appropriate for color recognition mode:

Example Result
Illustrations that are the same light color as the background image image
Illustrations that are the same dark color as the background image


The cutting data is created without converting the illustration to grayscale. Creating data in this mode may take longer, depending on the pattern.

 

 

 

 

 

Solution 4

 

The scanner glass may be dirty.  Clean the scanner glass inside the machine. For details, refer to Care and Maintenance (Cleaning the Scanner Glass).

 

▲ TOP

 

 

 

 

Problem 3: The scanned image is red.

 

Solution

 

Did you peel off the blue tape when using an optional scanning mat?
If not, peel off the blue tape from the optional scanning mat before scanning.

 

▲ TOP

 

 

 

Problem 4: The scan image is out of focus.

 

Solution

 

Set the scanner lever position on the left of the machine to "1".

image
 

▲ TOP

 

 

 

Problem 5: When converting the patterns to cutting data, [Cannot operate when there are too many patterns.] message appeared.

 

When converted to cutting data, more than the maximum number of patterns than the maximum number of patterns have been detected or are being saved as cutting data.
 

Depending on the machine model, the maximum number of patterns will differ. Check the [Maximum Pattern Number] under [Machine Information] of the settings screen.

image image image

 

 

 

Solution1

 

Reduce the number of patterns being used. Small patterns (dotted lines, etc.) can be excluded from cutting data by using [Ignore Object Size]. For details on adjustment of [Ignore Object Size], refer to "Solution 2" in the "Problem 1".

 

 

 

Solution2

 

Adjust the scanning area.

 

▲ TOP

 

If your question was not answered, have you checked other FAQs?

Have you checked the manuals?

If you need further assistance, please contact Brother customer service:

Related Models

SDX1200

Content Feedback

To help us improve our support, please provide your feedback below.

Step 1: How does the information on this page help you?

Step 2: Are there any comments you would like to add?

Please note this form is used for feedback only.