Innov-is A80

FAQs & Troubleshooting

FAQs & Troubleshooting

Tangled thread on wrong side of fabric

Symptom

  • The thread becomes tangled on the wrong side of the fabric.
    img01

  • After starting sewing, a rattling noise is made and sewing cannot continue.
  • Looking under the fabric, there is tangled thread in the bobbin case.
    img02

 

 

Cause

Incorrect upper threading

 

If the upper thread is incorrectly threaded, the upper thread passed through the fabric cannot be firmly pulled up and the upper thread becomes tangled in the bobbin case, causing a rattling noise.

 

 

Remedy/check details

Remove the tangled thread, and then correct the upper threading.

 

 

  1. Turn off the sewing machine.

     
  2. Remove the tangled thread. If it cannot be removed, cut the thread with scissors.
    img03

    For details, refer to “How do I clean the race?”.



     
  3. Remove the upper thread from the machine.

    If the bobbin was removed from the bobbin case, refer to “How do I set the bobbin?” to correctly install the bobbin.


     
  4. Raise the presser foot lever to raise the presser foot.
    img13

    If the presser foot is not raised, the machine cannot be threaded.


     
  5. Turn on the sewing machine.

     
  6. Press img04 (Needle position button) once or twice to raise the needle.
    >> The needle is correctly raised when the mark on the handwheel is at the top, as shown below. Check the handwheel and, if this mark is not at this position, press img05 (Needle position button) until it is.
    img06

     
  7. Turn off the machine.

    Before threading the needle, be sure to turn off the machine, otherwise injuries may occur if the "Start/Stop" button or any other button is pressed, causing the machine to start operating.


     
  8. Pass the thread under the thread guide, then under the thread guide cover and to the front.
    img14 (1) Thread guide
    (2) Thread guide cover

     
  9. Pass the thread through the thread channel in the order shown below.
    img15

     
  10. Make sure that the thread is passed into the thread take-up lever as shown below.
    img16

     
  11. Slide the thread behind the needle bar thread guide.
    The thread can easily be slid behind the needle bar thread guide by holding the thread in your left hand, then feeding the thread with your right hand, as shown. Make sure that the thread is passed through to the left of the tab of the needle bar thread guide.
    img17 (1) Needle bar thread guide
    (2) Tab

     
  12. Pull the end of the thread, which has been passed through the needle bar thread guide, to the left, then pass the thread through the notch of the threader thread guide, and then firmly pull the thread from the front and insert it into the slit of the threader thread guide disk marked “7” all the way.
    img18
    (1) Notch of the threader thread guide
    (2) Threader thread guide disk

     
  13. Cut the thread with the thread cutter on the left side of the machine.
    img19
    • If the thread is pulled through and cannot be cut correctly, lower the presser foot lever so that the thread is held in place before cutting the thread. If this operation is performed, proceed to step 15.
    • When using thread that quickly winds off the spool, such as metallic thread, it may be difficult to thread the needle if the thread is cut. Therefore, instead of using the thread cutter, pull out about 8 cm (approx. 3 inches) of thread after passing it through the threader thread guide disk (marked “7”).
      img20
      (1) 8 cm (approx. 3 inches) or more

     
  14. Lower the presser foot lever to lower the presser foot.
    img21

     
  15. Lower the needle threader lever on the left side of the machine as much as possible to make the hook turn.
     

    img22

    (1) Needle threader lever
    (2) Needle
    (3) Hook

    * After the threader thread guide disk is lowered (A), the hook turns (B).

    If the needle is not raised to it's highest position, the needle threader cannot thread the needle. Turn handwheel counterclockwise until the needle is at its highest position. The needle is correctly raised when the mark on the handwheel is at the top, as shown under step 6.


     
  16. Raise the needle threader lever slowly.
    img23

     
  17. Carefully pull the end of thread that was passed through the eye of the needle.
    If the needle was not completely threaded, but a loop in the thread was formed in the eye of the needle, carefully pull the loop through the eye of the needle to pull out the end of the thread.
    img24

     
  18. Raise the presser foot lever, pass the end of the thread through and under the presser foot, and then pull out about 5 cm (approx. 2 inches) of thread toward the rear of the machine.
    img25

 

If your question was not answered, have you checked other FAQs?

Have you checked the manuals?

If you need further assistance, please contact Brother customer service:

Related Models

Innov-is A80

Content Feedback

To help us improve our support, please provide your feedback below.

Step 1: How does the information on this page help you?

Step 2: €Are there any comments you would like to add?

Please note this form is used for feedback only.