Innov-is 4000D/4000

FAQs & Troubleshooting

FAQs & Troubleshooting

How do I thread my machine using the Automatic Threading Button?

Press  in that order to display a video example of the operation on the LCD.

Follow the steps explained below to complete the operation.

 

 

 

  • Be sure to thread the machine properly. Incorrect threading can cause the thread to tangle and break the needle, leading to injury.
  • When using accessories not included with this machine, attach the accessory to the machine after threading the machine.
  • Never use a thread weight of 20 or lower. It may cause malfunctions.

 

 

 

  • The automatic threading function can be used with sewing machine needles 75/11 through 100/16.
  • Thread such as transparent nylon monofilament thread and thread with a thickness of 130/20 or thicker cannot be used with the automatic threading function.
  • The automatic threading function cannot be used with the wing needle or the twin needle.
    In these cases, instead of using the automatic threading function, manually pass the thread through the machine and the eye of the needle.
    See the following FAQ.

    How do I manually thread my machine?
    How do I thread my machine for use with the twin needle option?.

 

 
  1. Turn the main power to ON.

  2. Press the "Needle Position" button to raise the needle.

    If you try to thread the needle automatically without raising the needle, the thread may not thread correctly.

     
  3. Pivot the spool pin so that it angles upward.

    Set the thread spool on the spool pin so that the thread unwinds from the front of the spool.

    Set the thread spool 1 Spool pin

    2 Spool cap

    3 Thread spool
  4. Push the spool cap onto the spool pin as far as possible, then return the spool pin to its original position.

     

    • If the thread spool and/or spool cap are set incorrectly, the thread may tangle on the spool pin and cause the needle to break.
    • Use the spool cap (large, medium, or small) that is closest in size to the thread spool. If a spool cap smaller than the thread spool is used, the thread may become caught in the slit on the end of the spool and cause the needle to break.

     

     

     

    When sewing with fine, cross-wound thread, use the small spool cap, and leave a small space between the cap and the thread spool.

    a small space between the cap and the thread spool 1 Spool cap(small)

    2 Thread spool(cross-wound thread)

    3 Space

     

     
  5. Holding the thread with your hands, slide the thread into the grooves on the thread guide plate.

    slide the thread into the grooves on the thread guide plate 1 Thread guide plate
  6. While holding the thread in your right hand, pass the thread through the thread guide in the direction indicated.

  7. When finished pulling the thread through the thread guide, cut the thread and leave the thread in position.

    cut the thread and leave the thread in position 1 Cutter
  8. Press the "Automatic Threading" button to have the machine automatically thread the needle.

    * The upper threading is finished.

    When the "Automatic Threading" button is pressed, the presser foot will be automatically lowered.

     
  9. In case the needle is not completely thread, slowly pull the loop of the thread through from the back of the needle.

    pull the loop of the thread 1 About 50mm(approx.2inches)

     

    If you use an improper needle and thread combinations, the hook may sometimes get caught in the needle.
    If this happens, remove the hook from the needle as described below.

     

     

     

    The needle thread carrier will automatically thread the needle when the "Automatic Threading" button is pressed.

    Be sure to keep your hands and other items away from the needle area, otherwise injuries may occur.

     

     
 

If your question was not answered, have you checked other FAQs?

Have you checked the manuals?

If you need further assistance, please contact Brother customer service:

Related Models

Innov-is 4000D/4000

Content Feedback

To help us improve our support, please provide your feedback below.

Step 1: How does the information on this page help you?

Step 2: Are there any comments you would like to add?

Please note this form is used for feedback only.