Innov-is F410

FAQs & Troubleshooting

FAQs & Troubleshooting

Basic procedure to sew stitches

  • While the machine is in operation, pay special attention to the needle location.
    In addition, keep your hands away from all moving parts such as the needle and handwheel, otherwise injuries may occur.
  • Do not pull or push the fabric too hard while sewing, otherwise injuries may occur or the needle may break.
  • Never use bent needles. Bent needles can easily break, possibly resulting in injuries.
  • Make sure that the needle does not strike basting pins, otherwise the needle may break or bend.

First, perform a trial sewing, using a piece of fabric and thread that are the same as those used for your project.

 

 

  1. Prepare the appropriate needle and thread for the type of fabric.
    For details, refer to "Combination of fabric, thread and needle".

    If necessary, replace the needle.
    For details, refer to "How do I change the needle?".

    For safety and best sewing results, use thread and needle appropriate for the fabric that you wish to sew.

    If the combination of the fabric, thread and needle is not correct, it may cause sewing problems or result in a poor finish to your sewing project.

     
  2. Wind thread onto a bobbin, and then install it into the machine.
    For details, refer to "How do I wind the bobbin?" , "How do I set the bobbin?".


     
  3. Thread the upper thread.
    For details, refer to "How do I thread the machine (Threading the upper thread)?".


     
  4. Select a stitch.
    img01
    • For details on how to select a stitch pattern for your model, refer to the "Stitch selection methods" and "Selecting a stitch pattern" section on the operation manual and the quick reference guide.
    • For details on the LCD viewing, refer to "Outline of viewing the LCD Screen".
    • For details on the built-in stitch patterns, refer to "Stitch Chart" on the operation manual and the quick reference guide.
    • If necessary, change the stitch width or stitch length.

      For details, refer to "How do I adjust a stitch width or length?".

    • The screen will vary depending on your machine model.


  5. Check the symbol for the presser foot shown in the LCD, and then attach the appropriate presser foot. Attach zigzag foot "J" in this procedure. (It is on the machine when purchased.)
     
    img02

    Always use the correct presser foot. If the wrong presser foot is used, the needle may strike the presser foot and bend or break, possibly resulting in injury.
    Refer to "Stitch Chart" for presser foot recommendations.


  6. Set the fabric under the presser foot. Hold the fabric and thread with your left hand, and rotate the handwheel counterclockwise or press img03 (Needle position button) to set the needle in the sewing start position.

    img04
     

  7. Lower the presser foot.

    img05

  8. Adjust the sewing speed with the sewing speed controller.
    (when using utility stitches)

    You can use this controller to adjust sewing speed during sewing.
    img06 (1) Fast
    (2) Slow


     
  9. Press the "Start/Stop" button to start sewing.
    (When the foot controller is plugged in, slowly press down on the foot controller.)

    Guide the fabric lightly by hand.

    img07
    When the foot controller is being used, you cannot start sewing by pressing the "Start/Stop" button.

     
  10. Press the "Start/Stop" button again to stop sewing.
    (When the foot controller is plugged in, remove your foot from the foot controller.)

    img08

     
  11. Press img09 (Thread cutter button) to trim the upper and bobbin threads.

    img10

    >> The needle will return to the up position automatically.
     
    • Do not press img11 (Thread cutter button) after the threads have been cut. Doing so could tangle the thread or break the needle and damage the machine.
    • Do not press img12 (Thread cutter button) when there is no fabric set in the machine. The thread may tangle, possibly resulting in damage.

    When cutting thread such as nylon monofilament thread, or other decorative threads, use the thread cutter on the left side of the machine.
    img13


  12. Raise the presser foot and remove the fabric.

    img14
     
  13. Check the sewing finish. If necessary, adjust the thread tension.
    For details, refer to "How to adjust the thread tension".

 

If your question was not answered, have you checked other FAQs?

Have you checked the manuals?

If you need further assistance, please contact Brother customer service:

Related Models

Innov-is F400, Innov-is F410

Content Feedback

To help us improve our support, please provide your feedback below.

Step 1: How does the information on this page help you?

Step 2: Are there any comments you would like to add?

Please note this form is used for feedback only.