CM600

FAQs & Troubleshooting

FAQs & Troubleshooting
  • Date: 10/07/2017
  • ID: faqh00100472_000

What should I do if the adjustment of the embossing template position failed?

If the adjustment of the embossing template position failed, determine the cause according to the symptom, and then resolve it.

After solving the problem, adjust the embossing template position again. For details, refer to "What should I do if the initial setting (position adjustment) for region embossing failed?"

 

 

The template for adjusting the embossing position extends past the material and is cut.

 

Not even one square in the template for adjusting the embossing position is overlapping.

 

Part of the template for adjusting the embossing position is not cut.

 

 

 

The template for adjusting the embossing position extends past the material and is cut.

  Possible Causes Remedy
1 Paper smaller than A4 or Letter size is being used. Use A4- or Letter-size thick paper to adjust the embossing template position.
2 The A4- or Letter-size paper used for making the adjustment is attached in the landscape orientation to the mat.

Attach the paper for adjusting the embossing template position in the portrait orientation to the mat, as shown below.
3 The A4- or Letter-size paper used for making the adjustment is not attached aligned with the upper-left corner of the mat.

Attach the paper for adjusting the embossing template position aligned with the upper-left corner of the mat.


 

 

Not even one square in the template for adjusting the embossing position is overlapping.

  Possible Causes Remedy
1 A blade incompatible with cutting the material for the adjustment is being used.

Replace with the holder (turquoise).
 
2 Paper thicker than specified is attached to the mat.

When adjusting the embossing position, use white A4- or Letter-size thick paper that has not been embossed.


The paper should have the same thickness as the adjustment sheet included with the Embossing Starter Kit, equivalent to 200 g/m2 (approx. 0.2 mm / 0.008 in).
3 While being cut, the paper for adjusting the embossing template position is shifted on the mat.

The mat’s adhesive strength has decreased.
Replace the mat with a new one.

The cutting mats used by this machine have been redeveloped with a different design, type, function, etc. For details, refer to Important information about Mat.
4 The blade is worn.

Replace the blade with a new one.
For details, refer to “Replacing the Blade”

 

 

 

Part of the template for adjusting the embossing position is not cut.

  Possible Causes Remedy
1 A blade incompatible with cutting the material for the adjustment is being used.

Replace with the holder (turquoise).
2 The amount that the blade extends from the holder is too small.

Remove the holder from the carriage, and then set the blade extension to 3.5.
If the material is not cut cleanly with the blade extension set to 3.5, increase the setting in increments of 0.5. If material is cut after increasing the setting by more than 0.5, too much of the blade may be extended, causing it to break. If the blade breaks, it may no longer be able to cut.

(1) Turn to the left to decrease the blade extension.

(2) Turn to the right to increase the blade extension.
3 The middle tack adhesive mat (pink and turquoise) is not used.

If any other cutting mat is being used, replace it with the middle tack adhesive mat.


The cutting mats used by this machine have been redeveloped with a different design, type, function, etc. For details, refer to Important information about Mat.
4 The mat’s adhesive strength has decreased, and the material is not secured.

Replace the mat with a new one.

 

The cutting mats used by this machine have been redeveloped with a different design, type, function, etc. For details, refer to Important information about Mat.
5 The blade is worn.

Replace the blade with a new one.
For details on replacing the blade, refer to “Replacing the Blade”
6 Material incompatible with making this adjustment is being used.

When adjusting the embossing position, use white A4- or Letter-size thick paper that has not been embossed.


The paper should have the same thickness as the adjustment sheet included with the Embossing Starter Kit, equivalent to 200 g/m2 (approx. 0.2 mm / 0.008 in).
7 Lint or dust has accumulated in the holder.

Clean the holder.
For details, refer to “Care and Maintenance (Cleaning the Holder)”
8 The cutting pressure is insufficient. If a part of the pattern remains uncut, the cutting pressure may be insufficient.
Increase the cutting pressure in increments of 1, and then perform trial cutting.

Related FAQs

If your question was not answered, have you checked other FAQs?

Have you checked the manuals?

If you need further assistance, please contact Brother customer service:

Related Models

CM260, CM300, CM600, CM600DX, CM700, CM750, CM800Q, CM840, CM900

Content Feedback

To help us improve our support, please provide your feedback below.

Step 1: How does the information on this page help you?

Step 2: Are there any comments you would like to add?

Please note this form is used for feedback only.

Submit