DCP-8250DN

FAQs & Troubleshooting

FAQs & Troubleshooting

What is the recommended paper?

We recommend to use the paper that is made for plain-paper copying and meets the following specification. 
This machine can use recycled paper that meets DIN 19309 specifications.
Basis weight 75-90 g/m2 (20-24 lb)
Thickness 80-110 μm
Roughness Higher than 20 sec.
Stiffness 90-150 cm3/100
Grain direction Long grain paper with a neutral Ph value, and a moisture content of approx. 5%
Volume resistivity 10e9-10e11 ohm
Surface resistivity 10e9-10e12 ohm-cm
Filler CaCO3 (Neutral)
Ash content Below 23 wt%
Brightness HIGHER Than 80%
Opacity HIGHER than 85%

 

  • DO NOT put different types of paper in the paper tray at the same time because it may cause paper jams or misfeeds.
  • For proper printing, you must choose the same paper size from your software application as the paper in the tray.
  • Avoid touching the printed surface of the paper immediately after printing.
  • Before you buy a lot of paper, test a small quantity to make sure that the paper is suitable.

For users in US/ Canada/ Latin America/ Europe region only:
We recommend the following paper types for this machine.

Paper Type

Europe

USA

Plain paper

Xerox Premier TCF 80 g/m2
Xerox Business 80 g/m2

Xerox 4200DP 20 lb
Hammermill Laser Paper 24 lb (90 g/m2)

Recycled paper Xerox Recycled Supreme 80 g/m2 (No specific brand recommended)
Labels Avery laser label L7163* Avery laser labels white #5160
Envelope Antalis River series (DL) (No specific brand recommended)

* Label Specifications
The machine will print on most types of labels designed for use with a laser machine. Labels should have an adhesive that is acrylic-based since this material is more stable at the high temperatures in the fuser unit.
Adhesives should not come in contact with any part of the machine, because the label stock may stick to the drum unit or rollers and cause jams and print quality problems. No adhesive should be exposed between the labels. Labels should be arranged so that they cover the entire length and width of the sheet. Using labels with spaces may result in labels peeling off and causing serious jams or print problems.
All labels used in this machine must be able to withstand a temperature of 200 degrees centigrade (392 degrees Fahrenheit) for a period of 0.1 seconds.

Do Not use the following type of paper, envelopes and labels.
Some types of paper may not perform well or may cause damage to your machine.

  • DO NOT use inkjet paper because it may cause a paper jam or damage your machine.
  • Preprinted paper must use ink that can withstand the temperature of the machine's fusing process 200 degrees centigrade (392 degrees Fahrenheit).
  • If you use bond paper, paper having a rough surface or paper that is wrinkled or creased, the paper may exhibit degraded performance.
  • DO NOT use paper:
    • that is highly textured
    • that is extremely smooth or shiny
    • that is curled or warped
      * 1 A curl of 2 mm (0.08 in.) or greater may cause jams to occur.
      Curled or warped
    • that is coated or has a chemical finish
    • that is damaged, creased or folded
    • that exceeds the recommended weight specification in this guide
    • with tabs and staples
    • with letterheads using low temperature dyes or thermography
    • that is multipart or carbonless
    • that is designed for inkjet printing

     

    If you use any of the types of paper listed above, they may damage your machine. This damage is not covered under any Brother warranty or service agreement.

     

  • DO NOT use envelopes:
    • that are damaged, curled, wrinkled, irregularly shaped, extremely shiny or textured envelopes.
    • with clasps, staples, snaps, tie strings, self-adhesive components, windows, holes, cutouts or perforations.
    • that are of a baggy construction, not sharply creased, embossed (have raised writing on them) or preprinted on the inside.
    • that were previously printed by a laser / LED printer.
    • that cannot be arranged when put in a pile.
    • that are made of paper that weighs more than the paper weight specifications for the machine.
    • with edges that are not straight or consistently square.
    • with glue on surface as shown in figure below
      Glue
    • with double flaps as shown in figure below
      Double flaps
    • with sealing flaps that are not folded down when purchased
    • with sealing flaps as shown in figure below
      Sealing flaps
    • with each side folded as shown in figure below
      Each sided folded


  • DO NOT use labels:
    that are damaged, curled, wrinkled or an unusual shape

    Label Spec


    • Avoid feeding labels with the carrier sheet exposed because your machine will be damaged.
    • Label sheets should not exceed the paper weight specifications above. Labels exceeding this specification may not feed or print properly and may cause damage to your machine.
    • Do not reuse or insert labels that have previously been used or are missing a few labels on the sheet.

If your question was not answered, have you checked other FAQs?

Have you checked the manuals?

If you need further assistance, please contact Brother customer service:

Related Models

DCP-7055, DCP-7055R, DCP-7055W, DCP-7055WR, DCP-7057, DCP-7057R, DCP-7057WR, DCP-7060D, DCP-7060DR, DCP-7065DN, DCP-7065DNR, DCP-7070DW, DCP-7070DWR, DCP-8110DN, DCP-8250DN, FAX-2840, FAX-2845, FAX-2845R, FAX-2940, FAX-2940R, HL-2130, HL-2130R, HL-2132, HL-2132R, HL-2135W, HL-2240, HL-2240D, HL-2240DR, HL-2240R, HL-2250DN, HL-2250DNR, HL-2270DW, HL-5440D, HL-5450DN, HL-5450DNT, HL-5470DW, HL-6180DW, HL-6180DWT, MFC-7360N, MFC-7360NR, MFC-7460DN, MFC-7860DW, MFC-7860DWR, MFC-8510DN, MFC-8520DN, MFC-8950DW, MFC-8950DWT

Content Feedback

To help us improve our support, please provide your feedback below.

Step 1: How does the information on this page help you?

Step 2: Are there any comments you would like to add?

Please note this form is used for feedback only.