Innov-is 600

FAQs & Troubleshooting

FAQs & Troubleshooting
  • Date: 22/04/2015
  • ID: faqh00000017_000

How do I sew a blind hem?

Secure the bottoms of skirts and pants with a blind hem. Sew a blind hem according to the following procedure.

 

Be sure to turn off the main power before replacing the pressor foot. Otherwise, injuries may occur if Start/Stop button is accidentally pressed and the machine starts sewing.

 

When the size of cylindrical pieces is too small to slide onto the arm or the length is too short, the fabric will not feed and desired results may not achieved.

 
  1. Reverse the skirt or pants.
    image 1 Wrong side of fabric
    2 Right side of fabric 
    3 Edge of fabric
    4 Bottom side

     

     

  2. Fold the fabric along the desired edge of the hem, and press.

    img
    <Seen img from the side>

    		 1 Wrong side of fabric
    2 Right side of fabric
    3 Edge of fabric
    4 Desired edge of hem


    <Thick fabric>


    <Normal fabric>

     

  3. Use a chalk to mark on the fabric about 5mm(3/16 inch) from the edge of the fabric, and then baste it.

    img
    <Seen img from the side>

    1 Wrong side of fabric
    2 Right side of fabric 
    3 Edge of fabric
    4 Desired edge of hem
    5 5mm (3/16 inch)
    6 Basting


    <Thick fabric>


    <Normal fabric>

     

     

  4. Fold back the fabric inside along the basting.

    img
    <Seen img from the side>


    1 Wrong side of fabric
    2 Right side of fabric 
    3 Edge of fabric
    4 Desired edge of hem
    5 5mm (3/16 inch)
    6 Basting
    7 Basting point

    <Thick fabric>

    <Normal fabric>

     

  5. Unfold the edge of fabric, and position the fabric with the wrong side facing up.

    img
    <Seen img from the side>

    		 1 Wrong side of fabric
    2 Right side of fabric 
    3 Edge of fabric
    4 Desired edge of hem
    5 Basting point
    6 Basting

    <Thick fabric>


    <Normal fabric>

     

  6. Attach Blind Stitch Foot "R" or the optional accessory Blind Stitch Foot "L".

    img

    		            　　　　　　 img
    the optional accessories "Blind Stitch Foot"  

    the

     

     

  7. Select a stitch. ( ex. Blind hem stitch  Blind hem stitch )
  8. Depending on your machine, remove the flat bed attachment and make free-arm sewing possible.
  9. Slide the part that you wish to sew onto the arm, make sure that the fabric feeds correctly, and then start sewing.
    img1 Arm

    >>　Blind Stitch Foot "R" ⇒ Step 10

    >>　Blind Stitch Foot "L" ⇒ Step 14


    Blind Stitch Foot "R"

     

     

  10. Position the fabric with the edge of the folded hem against the guide of the presser foot, and then lower the presser foot lever.
    img 1 Wrong side of fabric
    2 Fold of hem
    3 Guide

     

     

  11. Adjust the stitch width until the needle slightly catches the fold of the hem.
    img 1 Needle drop point

     

     

    When you change the needle drop point, raise the needle, and then change the stitch width.
    img 1 Thick fabric
    2 Normal fabric

     

     

    • If the needle catches too much of the hem fold

      <Thick fabric>
      img

       

      <Normal fabric>
      img
      1 Wrong side of fabric
      2 Right side of fabric

      The needle is too far to the left.
      Press decrease key to decrease the stitch width so that the needle slightly catches the fold of the hem.
    • If the needle does not catch the hem fold

      <Thick fabric>
       
      img

       

      <Normal fabric>
      img
      1 Wrong side of fabric
      2 Right side of fabric

      The needle is too far to the right.
      Pressincrease key to increase the stitch width so that the needle slightly catches the fold of the hem.

     

     
  12. Sew with the fold of the hem against the presser foot guide.
  13. Remove the basting stitching and reverse the fabric.
    img
    1 Wrong side of fabric
    2 Right side of fabric


    ***** Procedure of Blind Stitch Foot "R" is Ends here. *****


    Blind Stitch Foot "L"

     

     

  14. Position the needle the distance you want the stitch to be from the edge of the fabric, and then lower the needle in that position.
    Turn the foot guide screw and carefully adjust to guide the fabric.
     img

    img

    1 folded hem
    2 screw 
    3 guide
    4 needle
    5 needle position

    *1 Right side of fabric
    *2 Wrong side of fabric
  15. Lower the foot.
  16. Sew with the fold of the hem against the presser foot guide.
  17. Remove the basting stitching and reverse the fabric.
    img
    1     Wrong side of fabric
    2 Right side of fabric
     

If your question was not answered, have you checked other FAQs?

Have you checked the manuals?

If you need further assistance, please contact Brother customer service:

Related Models

BC-2100/BC-2100PRW, BC-2500, BM-3500/2600, BM-3600, CS-6000/6000b/6000t, CS-8060, DS-120, DS-140, FS101, FS155, FS50, FS70, Innov-is 1000, Innov-is 1200, Innov-is 1250D, Innov-is 1500D/1500, Innov-is 200/200QE, Innov-is 210, Innov-is 400, Innov-is 4000D/4000, Innov-is 410, Innov-is 4500D, Innov-is 500D, Innov-is 600, Innov-is 610, Innov-is 6700D, Innov-is 6750D, Innov-is 900, Innov-is 950, Innov-is 980D, Innov-is BQ2500, Innov-is BQ3100, Innov-is I / Innov-is 6000D, Innov-is VM5100, Innov-is VM5200, Innov-is VM6200D, Innov-is VQ2400, Innov-is VQ3000, LS-2125/2160, LS-2150, NS10, NS15, NS20, NS25, NS30/30LE, NS35, NS50, NS55, NX-200/200QE, NX-250, NX-400Q/400, NX-450, NX-600, PE-190D, PS-53/55/57, QC-1000, QC-2000, SL500, SuperGalaxie 3000/3000C/3000D/3100D, XL-2120/2220/2230/2240, XL-2600/2620/2630, XL-5500, XL-5700, XL-6040/6050

Content Feedback

To help us improve our support, please provide your feedback below.

Step 1: How does the information on this page help you?

Step 2: Are there any comments you would like to add?

Please note this form is used for feedback only.

Submit